DeWalt DWX726 instruction manual English

Page 10

English

WARNING: Planers MUST be mounted in the orientation shown in Figure 16.

FIG 16

WARNING: The cuttinghead MUST be raised on all miter saws, compound miter saws and sliding compound miter saws. All sliding compound miter saws MUST be locked in the rear position. Failure to do so may result in serious personal injury.

WARNING: STABILITY HAZARD. Stay alert. The stand may tip during this procedure. Serious injury may result.

1.Ensure the tool is securely mounted to the stand and is turned off and disconnected from power source.

2.Place a 2-1/2 inch (63.5 mm) thick block of wood (FF) under the front leg (GG) of the stand so that the front leg is raised 2-1/2 inches (63.5 mm) off the floor.

FIG 17

GG

HH

FF

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before installing and removing accessories, before adjusting or changing set- ups or when making repairs. An accidental start-up can cause injury.

WARNING: For your own safety, use two or more people to perform the stability test or serious injury could result.

3.With one person in front of the stand, and the other person behind, lift the front of the stand slightly, remove the block of wood, and allow the stand to drop to the floor.

4.Perform this same test with the block of wood under the rear leg (HH).

5.If the stand tends to tip to the front, reposition the tool toward the rear of the stand. If the stand tends to tip to the rear, reposition the tool forward. Make your adjustment, then repeat the test.

8

Image 10

Contents Guide Dutilisation Manual DE Instrucciones DWX726 Universal Miter Saw/Planer Stand Components ListDeﬁnitions Safety Guidelines Safety RulesTools Required Carton ContentsAssembly Components FigAttaching the Wheel and Storage Foot Connector FIG Attaching the Wheels FIGAttaching the Storage Foot FIG Attaching the Handle FIGTo Raise and Lower the Stand FIG Attaching the Extension Work Supports Attaching the Cord WrapsAttaching the Tool FIG Mounting slots align the with holes in the tool’s feetProduct Stability Test FIG English Storage and Transportation To Adjust Extension Work Support HeightOperation To Extend the Extension Work Supports FIGYear Free Service Accessories RepairsThree Year Limited Warranty DAY Money Back GuaranteeEnglish Plate-forme mobile pour scie à onglet/raboteuse DWX726 Description de l’établiDéﬁnitions lignes directrices en matière de sécurité Règles DE SécuritéDescription Fig Contenu du cartonOutils nécessaires MontageInstallation DU Raccord DE ROUE/PIED DE Rangement FIG Installation DE LA Rallonge DE PiedInstallation DES Roues FIG Installation DE LA Poignée FIG Installation DU Pied DE Rangement FIGPour Lever ET Abaisser LA Plateforme FIG Installation DES Crochets Pour Enrouler LE Cordon Électrique Installation DE L’OUTIL FIGDoit Être Test DE Stabilité FIG Extension DES Supports Télescopiques FIG UtilisationRéglage Vertical DU Support Télescopique Réparations AccessoiresStockage ET Transport Garantie limitée trois ansService D’ENTRETIEN Gratuit DE 1 AN Garantie DE Remboursement DE 90 JoursEspañol Lista de piezasDeﬁniciones Normas de seguridad Reglas DE SeguridadComponentes Fig Contenido de la cajaHerramientas requeridas EnsamblajeInstalación DE LA Pata DE Extensión Instalación DE LAS Ruedas FIGInstalación DE LA Barra DE Sujeción FIG Instalación DEL PIE Para Almacenamiento FIGPara Subir O Bajar EL Soporte FIG Instalación DE LA Extensión DEL Soporte Para TareasInstalación DE LOS Soportes Para Enrollar EL Instalación DE LA Herramienta FIGAgujeros CON UN Diámetro Prueba DE Estabilidad DEL Producto FIG Operación Para Extender LAS Extensiones DE Soporte Para Tareas FIGAccesorios Almacenamiento Y TransporteReparaciones Garantía limitada de tres años Póliza de GarantíaExcepciones Servicio Gratuito DE 1 AÑO Garantía DE Reembolso DE Dinero DE 90 Días