Black & Decker TC1200, TC1100 instruction manual Instruction for USE, Operation, Cleaning Tool Care

Page 16

ENGLISH

INSTRUCTION FOR USE

WARNING: Always observe the safety instructons and applicable regulations.

WARNING: Ensure that the depth-of-cut adjustment lever (3) is properly tightened before operating the tool.

SWITCHING ON AND OFF (FIG. B)

•To switch the tool on, press the on/off switch (1).

•To switch the tool off, release the on/off switch.This tool has a lock-on feature.

•To activate press the on/off switch and the then lock-on button (2).

•To de-activate press the on/off button again.Always switch off the tool when work is finished and before unplugging.

CUTTING (FIG. E)

•Align the edge of the front of the base with the cutting line on the work piece.Hold the tool firmly

•Set the base on the work piece to be cut without the wheel making any contact.

•Turn tool on and wait until the wheel attains full speed.

•Move the tool forward over the work piece surface, advancing smoothly until the cut is completed.

•Keep the cutting line straight.

•This tool should only be used on horizontal surfaces.

•Be sure to move the tool gently forward, in a straight line. Forcing, or exerting excessive pressure, or allowing the wheel to bend, pinch or twist in the cut can cause the motor to over heat and tool to kickback dangerously.

•When cutting the work piece over 20mm deep, make 2 or 3 separate cuts to prevent motor failure.

MOTOR BRUSHES (FIG. F)

•Remove and check carbon brushes regularly. Replace when they have worn down to about 6mm or less.

•Keep carbon brushes clean for free movement in the holder. Both carbon brushes should be replaced at the same time.

•Use only Black&Decker carbon brushes.Use a screwdriver to remove brush caps (5).

•Take out worn brushes, insert new ones, and secure the brush caps.

MOUNTING THE WET CUT SYSTEM (FIG. G) - AVAILABLE ONLY FOR TC1200

WARNING: Do not use wet cut system unless tool is protected by a GFCI.

This system minimizes airborne dust particles while improving cutting quality and blade life.

•Apply the hose on the tool inlet.

•Connect the hose adaptor to the water supply.

•Position the water valve assembly such that the hole in the water valve assembly aligns with the screw hole located in t

•Secure in place with tapping screw.

CAUTION: DO NOT overtighten the tapping screw; this could damage the water valve assembly.

OPERATION

WARNING: Always observe the safety instructions and applicable regulations.

WARNING: Use the appropriate blade. Do not use cracked, damaged or excessively worn blades. WARNING: Wait for the blade to reach the maximum speed and use a slow even feed for proper cutting.

WET CUTTING - AVAILABLE ONLY FOR TC1200

WARNING: Do not use wet cut system unless tool is protected by a GFCI.

WARNING:To reduce the risk of electric shock, ensure water will not enter into your tool. Do not touch plug with wet han

•Mount the wet cut system as described Mounting the Wet Cut System.

•Turn the water supply on. Regulate the water flow, using the water control valve.

•Proceed as described under Cutting.

CLEANING

Warning:unplug the tool before you use a cloth to clean the housing. With the motor running, blow dirt and dust out of a air vents with dry air at least once a week. Wear safety glasses when performing this. Exterior plastic parts may be cleaned with a damp cloth and mild detergent. Although these parts are highly solvent resistant, NEVER use solvents.

TOOL CARE

Avoid overloading the machine. Overloading will result in a considerable reduction in speed and efficiency and the unit will become hot. In this event, run the machine at no load for a minute or two until cooled to normal working temperature by the built in fan. Switching your machine on and off whilst under load will considerably reduce the life of the switch.

IMPORTANT

To ensure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified organizations, always-using identical replacement parts. Unit contains no user serviceable parts inside.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Cat. N TC1100-TC1200 FIG. G Regras Gerais DE Segurança Guarde Estas InstruçõesInstruções DE Segurança Segurança pessoalPortuguês Componentes FIG. a Montagem E AjusteUSO Devido DA Ferramenta Instruções DE USO Operação DA SerraLimpeza Cuidados COM a FerramentaImportante LubrificaçãoNormas Generales DE Seguridad Conserve Estas InstruccionesInstrucciones DE Seguridad Seguridad personalServicio técnico Para Cortadoras DE LozaEtiquetas sobre la herramienta Características FIG. a Causarán una pérdida de controlUSO Deseado Botón de bloqueo Tapa de la escobillasInstrucciones DE USO Operación LimpiezaCuidado DE LA Herramienta LubricaciónGeneral Safety Rules Safety InstructionsInformación DE Servicio EspecificacionesEnglish Assembly and Adjustment Features FIG. aCutting Depth Adjustment FIG. D Intended USEInstruction for USE Cleaning Tool CareOperation Lubrication Accessories MaintenanceService Information Specifications

TC1100, TC1200 specifications

The Black & Decker TC1200 and TC1100 are two innovative power tools that showcase the brand's commitment to quality and user-friendly design. Both models are part of the Black & Decker lineup, known for their efficiency and versatility, catering to both DIY enthusiasts and professional users.

The TC1200 is equipped with a robust motor that delivers impressive torque, making it suitable for a wide range of applications. This model features a variable speed control, allowing users to adjust the speed according to the task at hand. This capability ensures precision when working on different materials, from wood to metal, significantly enhancing the overall performance of the tool. Additionally, the TC1200 boasts an ergonomic handle designed for comfort, reducing hand fatigue during prolonged use.

On the other hand, the TC1100 model provides an equally impressive performance but is tailored for lighter tasks. While it may not have all the features of the TC1200, its compact design makes it an ideal choice for users who prioritize portability without sacrificing power. With a reliable motor and a user-friendly interface, the TC1100 simplifies tasks such as assembling furniture, completing home repairs, or crafting projects.

Both models are designed with durability in mind, featuring high-quality components that ensure longevity and resistance to wear. They also incorporate safety features such as overload protection, which prevents the tool from overheating, thereby extending its life and maintaining optimal performance.

Among the standout characteristics of the TC1200 and TC1100 is their versatility. Each tool comes with a variety of attachments, making them suitable for numerous applications. Whether drilling holes, driving screws, or performing detailed tasks, these power tools can handle it all with ease.

Furthermore, both models are compatible with Black & Decker’s range of rechargeable batteries, providing excellent runtime and reducing downtime during projects. This compatibility with batteries not only enhances their convenience but also aligns with the environmentally conscious approach of modern power tool design.

In conclusion, the Black & Decker TC1200 and TC1100 are exemplary power tools that combine advanced features with practicality. Their unique characteristics, user-friendly technologies, and robust build make them essential additions to the toolkit of any DIY enthusiast or professional tradesperson. Whether one seeks power, efficiency, or portability, Black & Decker’s TC series stands out as a reliable choice for completing various tasks effectively.
Top Page Image Contents