Bosch Power Tools 1677MDT manual Accessories, Tool’s

Page 14
! WARNING

BM 2610917132 10-03 10/28/03 11:07 AM Page 14

TWIST-TO-LOCK CONNECTOR INSTRUCTIONS FOR MODEL 1677MDT ONLY 20 AMP, 125

VOLT “TWIST-TO-LOCK”

The Model 1677MDT is equipped with a NEMA L5-20P“Twist-To-Lock” male connector as shown.

Use only a 3-wire extension cord which has a mating “Twist-To-Lock” female connector on one end and a 3-prong grounding plug on the other end. (See Electrical Safety section on page 2 for grounding information.)

Accessories

If an extension cord is necessary, a cord with adequate size conductors that is capable

of carrying the current necessary for your tool must be used. This will prevent

excessive voltage drop, loss of power or overheating. Grounded tools must use 3- wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

 

 

 

 

 

 

 

 

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

25

50

100

150

15

30

60

120

 

3-6

 

 

 

 

 

 

 

 

18

16

16

14

0.75

0.75

1.5

2.5

6-8

18

16

14

12

0.75

1.0

2.5

4.0

8-10

18

16

14

12

0.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

12-16

14

12

 

 

 

 

 

 

 

 

 

*

Blade

(*= standard equipment)

*

Wrench

(**= optional accessories)

** Rip Fence

 

-14-

Image 14
Contents 2610917132 Power Tool Safety Rules Work AreaSafety Rules for Circular Saws Tool Use and CareCauses and Operator Prevention Kickback Or Kickback from the workpiece as the saw is restarted Symbols Functional Description and Specifications Circular SawAssembly VARI-TORQUE ClutchInstalling Power Cord FIG. aOperating Instructions Depth AdjustmentBevel Adjustment Cutting Angle CheckCutting MASONRY/METAL SwitchGeneral Cuts Pocket CutsRIP Board Guide Cutting Large SheetsRIP Cuts Carbon Brushes MaintenanceTool Lubrication BearingsAccessories Tool’sSécurité des personnes Sécurité électrique Règles de Sécurité GénéralesAire de travail Conservez CES InstructionsRéparation Consignes de sécurité pour scies circulairesUtilisation et entretien des outils La réparation des outils électriques doit être confiéeCauses ET PRÉVENTION, PAR Lopérateur DU Rebond Le plomb provenant des peintures à base de plomb Symboles NOMDescription fonctionnelle et spécifications Scie circulaireAssemblage Embrayage « VARI-TORQUE »Installation du cordon dalimentation LE Système DE RaccordVérification DE L’ANGLE DE Coupe Consignes de fonctionnementRéglage DE LA Profondeur DE Coupe Réglage DE LA Coupe EN BiseauMouvement de la garde inférieure InterrupteurCoupes Régulierès Sciage DES Matériaux DE Maçonnerie ET DES MétauxUtilisation D’UNE Planche Comme Guide DE Refente Coupe DE Grandes FeuillesCoupes DE Refente Service Entretien20 AMP., 125 Volts AccessoiresRaccord « TWIST-TO-LOCK » Pour Modèle 1677MDT Uniquement Seguridad eléctrica Normas de seguridad para herramientas mecánicasArea de trabajo Seguridad personalNormas de seguridad para sierras circulares ServicioCausas DEL Retroceso Y SU Prevencion POR EL Operador Embrague DE PAR Motor VariableBM 2610917132 10-03 10/28/03 1107 AM Símbolos De Ni-CdCapacidades máximas Descripción funcional y especificacionesSierra circulare Ensamblaje Embrague DE PAR Motor VariableInstalación del cordón energía EL Sistema DE ConexiónAjuste DE Inclinación Instrucciones de funcionamientoAjuste DE Profundidad Guía DE LíneaMovimiento libre del protector inferior Guía DE InterruptorCortes Generales Corte DE Mamposteria Y MetalTABLERO-GUIA Para Cortar AL Hilo Corte DE Planchas GrandesCortes AL Hilo Mantenimiento LimpiezaAccesorios CapacidadBM 2610917132 10-03 10/28/03 1107 AM Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools