Carrier 52S manual To Remove the AIR Discharge Grille, To Remove the TOP Cover Ð Remove the screw

Page 7

TO REMOVE THE AIR DISCHARGE GRILLE

1.Remove the 2 screws on each end of the air discharge grille as shown in Figure 14.

2.Lift and rotate back the bottom edge of the discharge grille and remove it.

FIGURE 14 Ð REMOVING AIR DISCHARGE GRILLE

TO REMOVE THE ALUMINUM TOP PANEL

Ð Remove one screw from each end of the aluminum top panel (located on the underside of the panel) as shown in Figure 15. On the left side of the unit, remove the screw closest to the side of the unit.

TOP PANEL

SCREW

FIGURE 15 Ð ALUMINUM TOP PANEL

TO REMOVE THE TOP COVER Ð Remove the screw

located in the middle of the top cover and remove the cover. See Figure 16.

FIGURE 16 Ð TOP COVER SCREW

7

Image 7

Contents Contents Service Technician GuideSummary of DANGERS, WARNINGS, and Cautions IntroductionModel Number Nomenclature To Remove the Unit from the Wall Sleeve General DisassemblyTo Disconnect Power for CORD- Connected Unit To Open the Control BOXDuct Extension Screws Removing the AIR Baffle To Access INDOOR-AIR Section ComponentsTo Remove the TOP Cover Ð Remove the screw To Remove the AIR Discharge GrilleTo Remove the Discharge Deck To Access OUTDOOR-AIR Section ComponentsTo Remove the Gusset Removing Stator Consider the following safety issues before beginning General CleaningCleaning and Safety Component Cleaning ScheduleTools Needed Monthly CleaningCleaning the Indoor AIR Filter Ð Remove Replacing the Indoor AIR Filter Ð AccessReplacing the Vent AIR Filter Cleaning the Vent AIR FilterChassis Accessing the Indoor and Outdoor Seasonal CleaningDisconnect ALL Power to Unit Section Components on Cleaning the Indoor and Outdoor CoilsAccessing the Indoor FAN and Indoor Coils sectionDisconnect ALL Power to the Unit Cleaning the Indoor FAN and FANCleaning the Heater Assembly Ð Once Rotary Compressor Components CompressorBasic Hermetic Compressor Electrical Measurements Compressor TroubleshootingBasic Compressor Troubleshooting Guide SHORTED/OPEN Windings Test Compressor ReplacementRemoving the Compressor Ð Follow the steps Disconnect all power to unitRefrigerant Charging Ð Every mechanical Installed Filter DrierCommon Causes Heater Failure HeatersHeater Removal Removing Heater Screws Typical 52S Unit Operating Controls Operating ControlsOutside or Vent AIR Ð Push the FAN only Description of Switch SettingsNON-USER Adjustable Switches High Heat or High Cool Ð Push buttonHeat Pump Units Figure Sequence of OperationHEAT/COOL Units Figure Cooling only Units FigureTools Needed Component Operation and TroubleshootingIndoor Thermostat Heat Pump Units Outdoor Frost Thermostat Heat Pump Units Indoor Thermostat IT CONTACTS, ALL 52SQ AA and CP ModelsCapacitor Test Locked OUTOutdoor Frost Thermostat Screws Electrical Components Removal and ReplacementComponent Locations Open Control BOX FAN Motor FAN Motor TroubleshootingBasic FAN Motor Electrical Tests Typical 265 Volt Motors FAN Motor Troubleshooting Chart Typical 208/230 Volt MotorsRemoval FAN Motor ReplacementField Temperature Charts 52S Series Page 52S Series Page 52S Series Page 52S Series Page 52S Series Page 52S Series Page 52S Series Page 52S Series Wiring Schematic 52SC Ð 208/230 V and 265 V AA and CP Units Wiring SchematicsWiring Schematic 52SE Ð 208/230 V and 265 V AA and CP Units Wiring Schematic 52SE Ð 208/230 V and 265 V RC Units Wiring Schematic 52SQ Ð 208/230 V and 265 V AA and CP Units Wiring Schematic 52SQ Ð 208/230 V and 265 V RC Units Most Frequent Ptac Service Questions