Cisco Systems 815 manual

Page 2

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

•Turn the television or radio antenna until the interference stops.

•Move the equipment to one side or the other of the television or radio.

•Move the equipment farther away from the television or radio.

•Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Corporate Headquarters Page Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Installing and Removing a Dimm C-4 ViiViii Audience and Scope OrganizationRelated Documentation Conventions Xii Xiii Xiv Page Xvi Xvii Commands XviiiCisco.com AccessibilityObtaining Documentation XixProduct Documentation DVD Ordering Documentation Documentation Store in the Cisco Marketplace at this URLXxi Documentation FeedbackCisco Product Security Overview Reporting Security Problems in Cisco Products XxiiXxiii Obtaining Technical AssistanceCisco Technical Support & Documentation Website Xxiv Submitting a Service RequestDefinitions of Service Request Severity Obtaining Additional Publications and Information XxvXxvi Key Features OverviewFeature Description Product Serial Number Location CiscoBack Panel Ports and LEDs Back Panel Ports and LEDsLabel/Color Description Front Panel LEDs WIC0 OKLED Label Color Description Router Memory Types of MemoryAmounts of Memory 815# show versionItems Included with the Cisco 815 Integrated Services Router Unpacking the RouterInstallation Before Installing the RouterConnecting the Router to Your Local Network Installation Connecting the Router to Your Local Network Connecting the Router to the Local Network Connecting Power to the Router Connecting the Power SupplyVerifying Your Installation Optional Installation Procedures Connecting a PCConnecting the Console Cable to the Router Connecting a Modem AUX port RJ-45 DB-9-to-DB-25 adapter Console cable ModemStacking the Router Assembling Stacking Clip and Fastener Stacking the Router Back View Unstacking the Router Unstacking the RouterOL-9558-01 Troubleshooting Contacting Your Cisco ResellerRecovering a Lost Password Determining the Configuration Register ValueConfiguration register is 0x2102 815# Resetting the Router Press Return. The following prompt appearsPrompt changes to the privileged Exec prompt Resetting the Password Resetting the Configuration Register ValueProblem Solving OK LED DiagnosticsTroubleshooting WICs and Cables Number of Blinks MeaningExample WIC-4ESW Troubleshooting the Power System Symptom Possible Causes Technical Specifications Operating Specifications Cabling Specifications Ethernet CablesEthernet Network Cabling Guidelines 10BASE-T 100BASE-TXSignal RJ-45 Pin DB-9 Pin DB-25 Pin Console Cable and AdapterOL-9558-01 Safety Warnings Opening the Chassis Figure C-1 Removing the Chassis Screws Installing and Removing a Dimm Locating ModulesRemoving a Dimm Release the latches Remove the DimmInstalling a Dimm Insert the Dimm Latches rotate to closed positionInstalling a VPN Module Screw StandoffFigure C-7 VPN Module Location Figure C-9 Retention Clip Location Figure C-10 Aligning the Retention Clip Center Post Figure C-11 Attaching the Retention Clip to the Motherboard Figure C-12 Securing the Standoff to the Router Motherboard Closing the Chassis Figure C-13 Attaching the Router Cover NumericsC IN-1ETH COL LED IN-2Dimm C-4 IN-3IN-4
Top Page Image Contents