Cisco Systems 815 manual Connecting the Console Cable to the Router

Page 44

Chapter 2 Installation

Optional Installation Procedures

Figure 2-3 Connecting the Console Cable to the Router

4

WIC

4ESW

ACT 4x

LNK

ACT 3x

Cisco

815

LNK

ACT 2x

LNK

WIC0OK

ACT 1x

LNK

CONSOLE

FDX

100

LINK

10/100

ETHERNET

AUX

2

1

HWIC-
CABLE-D-2	ON	DS	LINK
CABLE	ON	US	LINK
		LINE	POWER
			POWER
	MODOK
		WIC
			1OK

+5,	+12,	-12	VDC

3

146793

1	Blue console cable	3	To PC or terminal

2	Console port	4	Cisco 815 integrated services router

Step 2 Connect the DB-9 end of the console cable to the console port (also called the serial port) on your PC. If this adapter does not fit your PC console port, you must provide an adapter that fits.

	Cisco 815 Integrated Services Router Hardware Installation Guide
2-8	OL-9558-01

Image 44

Contents Corporate Headquarters Page Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Installing and Removing a Dimm C-4 ViiViii Audience and Scope OrganizationRelated Documentation Conventions Xii Xiii Xiv Page Xvi Xvii Commands XviiiAccessibility Obtaining DocumentationCisco.com XixProduct Documentation DVD Ordering Documentation Documentation Store in the Cisco Marketplace at this URLXxi Documentation FeedbackCisco Product Security Overview Reporting Security Problems in Cisco Products XxiiXxiii Obtaining Technical AssistanceCisco Technical Support & Documentation Website Xxiv Submitting a Service RequestDefinitions of Service Request Severity Obtaining Additional Publications and Information XxvXxvi Key Features OverviewFeature Description Product Serial Number Location CiscoBack Panel Ports and LEDs Back Panel Ports and LEDsLabel/Color Description Front Panel LEDs WIC0 OKLED Label Color Description Router Memory Types of MemoryAmounts of Memory 815# show versionItems Included with the Cisco 815 Integrated Services Router Unpacking the RouterInstallation Before Installing the RouterConnecting the Router to Your Local Network Installation Connecting the Router to Your Local Network Connecting the Router to the Local Network Connecting Power to the Router Connecting the Power SupplyVerifying Your Installation Optional Installation Procedures Connecting a PCConnecting the Console Cable to the Router Connecting a Modem AUX port RJ-45 DB-9-to-DB-25 adapter Console cable ModemStacking the Router Assembling Stacking Clip and Fastener Stacking the Router Back View Unstacking the Router Unstacking the RouterOL-9558-01 Troubleshooting Contacting Your Cisco ResellerRecovering a Lost Password Determining the Configuration Register ValueConfiguration register is 0x2102 815# Resetting the Router Press Return. The following prompt appearsPrompt changes to the privileged Exec prompt Resetting the Password Resetting the Configuration Register ValueProblem Solving OK LED DiagnosticsTroubleshooting WICs and Cables Number of Blinks MeaningExample WIC-4ESW Troubleshooting the Power System Symptom Possible Causes Technical Specifications Operating Specifications Cabling Specifications Ethernet CablesEthernet Network Cabling Guidelines 10BASE-T 100BASE-TXSignal RJ-45 Pin DB-9 Pin DB-25 Pin Console Cable and AdapterOL-9558-01 Safety Warnings Opening the Chassis Figure C-1 Removing the Chassis Screws Installing and Removing a Dimm Locating ModulesRemoving a Dimm Release the latches Remove the DimmInstalling a Dimm Insert the Dimm Latches rotate to closed positionInstalling a VPN Module Screw StandoffFigure C-7 VPN Module Location Figure C-9 Retention Clip Location Figure C-10 Aligning the Retention Clip Center Post Figure C-11 Attaching the Retention Clip to the Motherboard Figure C-12 Securing the Standoff to the Router Motherboard Closing the Chassis Figure C-13 Attaching the Router Cover NumericsC IN-1ETH COL LED IN-2Dimm C-4 IN-3IN-4