Cisco Systems 815 manual Verifying Your Installation

Page 42

Chapter 2 Installation

Verifying Your Installation

1

Power supply	2	Power socket

Step 2 Connect one end of the separate power cord to the socket on the power supply.

Step 3 Connect the other end of the separate power cord to a power outlet.

Step 4 Press the router power switch to ON ( ).

Step 5 Confirm that the router has power by checking that the PWR LED on the front panel is on.

Verifying Your Installation

You can verify that you have correctly installed the router by checking the following LEDs:

•PWR (front panel)—On when power is being supplied to the router.

•OK (front panel)—On when the router software is loaded and functional. Blinking indicates that the router is performing a power-onself-test (POST).

•WIC0/WIC1 OK (back panel)—On when the WIC is correctly installed in the corresponding WIC slot.

•ETH ACT (front panel)—Blinking when there is network traffic on the local 10/100 Ethernet LAN.

•WIC0 ACT or WIC1 ACT (front panel)—Varies, depending on the WIC installed. See Table 1-4in Chapter 1, “Overview.”

•LINK (back panel)—On when the router is correctly connected to the local Ethernet LAN through the 10/100 ETHERNET port.

•MOD OK (back panel)—On when the VPN hardware encryption module is installed and recognized by the Cisco IOS software.

	Cisco 815 Integrated Services Router Hardware Installation Guide
2-6	OL-9558-01

Image 42

Contents Corporate Headquarters Page Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Installing and Removing a Dimm C-4 ViiViii Audience and Scope OrganizationRelated Documentation Conventions Xii Xiii Xiv Page Xvi Xvii Commands XviiiCisco.com AccessibilityObtaining Documentation XixProduct Documentation DVD Ordering Documentation Documentation Store in the Cisco Marketplace at this URLDocumentation Feedback Cisco Product Security OverviewXxi Reporting Security Problems in Cisco Products XxiiObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteXxiii Submitting a Service Request Definitions of Service Request SeverityXxiv Obtaining Additional Publications and Information XxvXxvi Key Features OverviewFeature Description Product Serial Number Location CiscoBack Panel Ports and LEDs Back Panel Ports and LEDsLabel/Color Description Front Panel LEDs WIC0 OKLED Label Color Description Router Memory Types of MemoryAmounts of Memory 815# show versionItems Included with the Cisco 815 Integrated Services Router Unpacking the RouterInstallation Before Installing the RouterConnecting the Router to Your Local Network Installation Connecting the Router to Your Local Network Connecting the Router to the Local Network Connecting Power to the Router Connecting the Power SupplyVerifying Your Installation Optional Installation Procedures Connecting a PCConnecting the Console Cable to the Router Connecting a Modem AUX port RJ-45 DB-9-to-DB-25 adapter Console cable ModemStacking the Router Assembling Stacking Clip and Fastener Stacking the Router Back View Unstacking the Router Unstacking the RouterOL-9558-01 Troubleshooting Contacting Your Cisco ResellerRecovering a Lost Password Determining the Configuration Register ValueConfiguration register is 0x2102 815# Resetting the Router Press Return. The following prompt appearsPrompt changes to the privileged Exec prompt Resetting the Password Resetting the Configuration Register ValueProblem Solving OK LED DiagnosticsTroubleshooting WICs and Cables Number of Blinks MeaningExample WIC-4ESW Troubleshooting the Power System Symptom Possible Causes Technical Specifications Operating Specifications Cabling Specifications Ethernet CablesEthernet Network Cabling Guidelines 10BASE-T 100BASE-TXSignal RJ-45 Pin DB-9 Pin DB-25 Pin Console Cable and AdapterOL-9558-01 Safety Warnings Opening the Chassis Figure C-1 Removing the Chassis Screws Installing and Removing a Dimm Locating ModulesRemoving a Dimm Release the latches Remove the DimmInstalling a Dimm Insert the Dimm Latches rotate to closed positionInstalling a VPN Module Screw StandoffFigure C-7 VPN Module Location Figure C-9 Retention Clip Location Figure C-10 Aligning the Retention Clip Center Post Figure C-11 Attaching the Retention Clip to the Motherboard Figure C-12 Securing the Standoff to the Router Motherboard Closing the Chassis Figure C-13 Attaching the Router Cover NumericsC IN-1ETH COL LED IN-2Dimm C-4 IN-3IN-4