Cisco Systems 815 manual Opening the Chassis

Page 70

Appendix C Installing and Upgrading Memory and Virtual Private Network Modules

Opening the Chassis

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning Read the installation instructions before you connect the system to its power source.

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.

Warning Hazardous network voltages are present in WAN ports regardless of whether power to the router is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the router first.

Opening the Chassis

In order to upgrade the Cisco 815 integrated services router memory, you must open the chassis. Opening the chassis requires a number one Phillips screwdriver.

Follow these steps to open the chassis:

Step 1 Make sure the router is turned off and is disconnected from the power supply.

Step 2 Turn the router upside down, and rest the top of the router on a flat surface.

Step 3 Use the number one Phillips screwdriver to remove the four screws that fasten the top and bottom of the chassis together, as shown in Figure C-1.

	Cisco 815 Integrated Services Router Hardware Installation Guide
C-2	OL-9558-01

Image 70

Contents Corporate Headquarters Page Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Installing and Removing a Dimm C-4 ViiViii Audience and Scope OrganizationRelated Documentation Conventions Xii Xiii Xiv Page Xvi Xvii Commands XviiiCisco.com AccessibilityObtaining Documentation XixProduct Documentation DVD Ordering Documentation Documentation Store in the Cisco Marketplace at this URLCisco Product Security Overview Documentation FeedbackXxi Reporting Security Problems in Cisco Products XxiiCisco Technical Support & Documentation Website Obtaining Technical AssistanceXxiii Definitions of Service Request Severity Submitting a Service RequestXxiv Obtaining Additional Publications and Information XxvXxvi Key Features OverviewFeature Description Product Serial Number Location CiscoBack Panel Ports and LEDs Back Panel Ports and LEDsLabel/Color Description Front Panel LEDs WIC0 OKLED Label Color Description Router Memory Types of MemoryAmounts of Memory 815# show versionItems Included with the Cisco 815 Integrated Services Router Unpacking the RouterInstallation Before Installing the RouterConnecting the Router to Your Local Network Installation Connecting the Router to Your Local Network Connecting the Router to the Local Network Connecting Power to the Router Connecting the Power SupplyVerifying Your Installation Optional Installation Procedures Connecting a PCConnecting the Console Cable to the Router Connecting a Modem AUX port RJ-45 DB-9-to-DB-25 adapter Console cable ModemStacking the Router Assembling Stacking Clip and Fastener Stacking the Router Back View Unstacking the Router Unstacking the RouterOL-9558-01 Troubleshooting Contacting Your Cisco ResellerRecovering a Lost Password Determining the Configuration Register ValueConfiguration register is 0x2102 815# Resetting the Router Press Return. The following prompt appearsPrompt changes to the privileged Exec prompt Resetting the Password Resetting the Configuration Register ValueProblem Solving OK LED DiagnosticsTroubleshooting WICs and Cables Number of Blinks MeaningExample WIC-4ESW Troubleshooting the Power System Symptom Possible Causes Technical Specifications Operating Specifications Cabling Specifications Ethernet CablesEthernet Network Cabling Guidelines 10BASE-T 100BASE-TXSignal RJ-45 Pin DB-9 Pin DB-25 Pin Console Cable and AdapterOL-9558-01 Safety Warnings Opening the Chassis Figure C-1 Removing the Chassis Screws Installing and Removing a Dimm Locating ModulesRemoving a Dimm Release the latches Remove the DimmInstalling a Dimm Insert the Dimm Latches rotate to closed positionInstalling a VPN Module Screw StandoffFigure C-7 VPN Module Location Figure C-9 Retention Clip Location Figure C-10 Aligning the Retention Clip Center Post Figure C-11 Attaching the Retention Clip to the Motherboard Figure C-12 Securing the Standoff to the Router Motherboard Closing the Chassis Figure C-13 Attaching the Router Cover NumericsC IN-1ETH COL LED IN-2Dimm C-4 IN-3IN-4