Cisco Systems 815 manual Installation Connecting the Router to Your Local Network

Page 39

Chapter 2 Installation

Connecting the Router to Your Local Network

Caution Do not connect a WAN cable to the card until you have completed the installation procedure.

Note For details about specific WAN interface cards (WICs), connecting the card to the WAN line, and configuring the interface with Cisco IOS software, see the Cisco Interface Cards Hardware Installation Guide.

Warning The ports labeled 10/100 ETHERNET and CONSOLE are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuits to the telephone network voltage (TNV) circuits. (To see translated versions of this warning, refer to the Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers document that came with the router.)

Follow these steps to connect the router to the local network:

Step 1 Connect one end of the cable to the yellow Ethernet port (labeled

10/100 ETHERNET) on the back panel of the router, as shown in Figure 2-1.

		Cisco 815 Integrated Services Router Hardware Installation Guide

	OL-9558-01			2-3
	OL-9558-01			2-3

Image 39

Contents Corporate Headquarters Page Cisco Systems, Inc. All rights reserved Page N T E N T S Installation Vii Installing and Removing a Dimm C-4Viii Organization Audience and ScopeRelated Documentation Conventions Xii Xiii Xiv Page Xvi Xvii Xviii CommandsXix AccessibilityObtaining Documentation Cisco.comDocumentation Store in the Cisco Marketplace at this URL Product Documentation DVD Ordering DocumentationDocumentation Feedback Cisco Product Security OverviewXxi Xxii Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteXxiii Submitting a Service Request Definitions of Service Request SeverityXxiv Xxv Obtaining Additional Publications and InformationXxvi Overview Key FeaturesFeature Description Cisco Product Serial Number LocationBack Panel Ports and LEDs Back Panel Ports and LEDsLabel/Color Description WIC0 OK Front Panel LEDsLED Label Color Description Types of Memory Router Memory815# show version Amounts of MemoryUnpacking the Router Items Included with the Cisco 815 Integrated Services RouterBefore Installing the Router InstallationConnecting the Router to Your Local Network Installation Connecting the Router to Your Local Network Connecting the Router to the Local Network Connecting the Power Supply Connecting Power to the RouterVerifying Your Installation Connecting a PC Optional Installation ProceduresConnecting the Console Cable to the Router AUX port RJ-45 DB-9-to-DB-25 adapter Console cable Modem Connecting a ModemStacking the Router Assembling Stacking Clip and Fastener Stacking the Router Back View Unstacking the Router Unstacking the RouterOL-9558-01 Contacting Your Cisco Reseller TroubleshootingDetermining the Configuration Register Value Recovering a Lost PasswordConfiguration register is 0x2102 815# Press Return. The following prompt appears Resetting the RouterPrompt changes to the privileged Exec prompt Resetting the Configuration Register Value Resetting the PasswordOK LED Diagnostics Problem SolvingNumber of Blinks Meaning Troubleshooting WICs and CablesExample WIC-4ESW Troubleshooting the Power System Symptom Possible Causes Technical Specifications Operating Specifications Ethernet Cables Cabling Specifications10BASE-T 100BASE-TX Ethernet Network Cabling GuidelinesConsole Cable and Adapter Signal RJ-45 Pin DB-9 Pin DB-25 PinOL-9558-01 Safety Warnings Opening the Chassis Figure C-1 Removing the Chassis Screws Locating Modules Installing and Removing a DimmRelease the latches Remove the Dimm Removing a DimmInsert the Dimm Latches rotate to closed position Installing a DimmScrew Standoff Installing a VPN ModuleFigure C-7 VPN Module Location Figure C-9 Retention Clip Location Figure C-10 Aligning the Retention Clip Center Post Figure C-11 Attaching the Retention Clip to the Motherboard Figure C-12 Securing the Standoff to the Router Motherboard Closing the Chassis Figure C-13 Attaching the Router Cover IN-1 NumericsCIN-2 ETH COL LEDIN-3 Dimm C-4IN-4