Craftsman 315.220381 owner manual Setting the Bevel Lock Lever, Starwasher Bevel, Bevellockleverin

Page 27

SETTING THE BEVEL LOCK LEVER

See Figures 18A -18C.

The bevel lock lever locks the blade at desired angles other than the preset positive stop angles. The bevel lock lever is preset at the factory but may need readjustment after shippingor extended use. Check for overUghtnessor looseness and make any neces- sary adjustments as follows:

The bevel lock lever is located on the front of the yoke assembly, near the bottom. It is attached to a clamp bolt that controlsthe amount of tightness.

•Pull the bevel lock lever forward to unlock it. Use the bevel index knob (just under the handle) to

rotate the motor approximately 30 °. Lock the bevel lock lever.

•If the bevel lock lever is difficultto lock, the clamp bolt needs to be loosened. If the motorcan be

forced out of position, the clamp belt needs to be tightened.

•Remove the socket screw (under the bevel lock lever) and star washer with a 1/8 in. hex key.

•Use the bevel lock handle as a wrench to tighten or loosen the clamp belt. The clamp bolt has a right- handed thread. Tighten it left to right.

•When the bolt is correctly set, remove the bevel lock lever from the clamp bolt and place it roughly parallel to the yoke assembly.

•Replace the socket screw and star washer. Re- check the tightness of the bevel lock lever. Repeat the steps above until the motor is secure when locked, and the bevel lock lever fits squarely against the yoke assembly.

STARWASHER

BEVEL

LOCKLEVER

1/8 In.HEXKEY------_

Fig. 18B

BEVELLOCKLEVERIN

CORRECTLOCKEDPosmoN

Fig. 18C

BEVEL BEVEL

LOCKLEVER INDEXKNOB MOTOR Fig. 18A

27	[RIIFTSMIIIr RADIALSAW31S.22_1

Image 27

Contents Ofess Ional Radial ARM SAWFull ONE Year Warranty on Craftsman Radial ARM SAW 28-29 Meaning Safety Alert Symbol SymbolAvoid Awkward Operations and Hand Be Sure the Blade Clears the Work RIP only Workpieces Longer than Grounding PIN Coverofgrounded Outletbox GroundinginstructionsChanging Voltage See FiguresBladearbor Gum BladeBevelAngleRAFTSNANRADIALSAW315,220381 Sawassemblyshownaspacked Cdef IIoII000 Level Io@CRE.ANTPARTS Inch Radii Arm SawAdvertencia Knowyourradialsaw See aYoke 19IIRFTSMRNRADIALSAW315.220381 FeatureslistSee Figures 9A-9D Miterscale Armlockknob Yokepivotlatch RIPFigures 9A and 9B Dustguide Holddown MOTOR13/6.5AMP- Powersthebladeand isSee Figure lOB Assembly and Adjustments sections beforeTighten. See Figure I OA See Figure I OAElevating Shaft Handwheel Screw Starwasher Mounting SAW to LEG Stand Attaching Elevating HandwheelSee Figure SAW Base LEG Sawbase Hexbolt Flat Washer LockwasherCarriagearm Lockknob Installing the Yoke AssemblyArmviewedfrombelow Armlockknob ARM CapscrewsBlade Arbor Mounttablesupports Usingtheseholelocations Removing the BladeAttaching Table Supports Yokelock Handle Setting the ARM Lock KnobArmcap Motor Yokelock Handle Assembly See Figures 17,4and 17BBevel Bevel Setting the Bevel Lock LeverStarwasher Bevel BevellockleverinColumn ARM Tube Support Rear Coverscrews HEXBOLT2 HEXNUT2 Adjusting the Column TubeTightening the ARM and Column See Figures 20A 20DSilverblack Screws Columnsupport Elevation AdjustmentRotation Adjustment ColumntubeAdjusting the Carriage Bearings CarriagebearingEccentricscrew Wrench Graspandhold Carriagebearing Rightside Tablesupport Leveling Table SupportsSee Figures 22A and 22B Blade Wrenchat Front ArmlockknobHexnut Installing the Front TableSee Figures 23A 23C 23ALeveling the Front Table See Figures 25A 25CReartablefence Spacertablefronttable Clamp Bracket Squarenut HoleBlade Rotation Hten WRENCH2 See Figures 27A 27C Installing RIP Scale Indicators Carriage SpeednutSpring Carriage Screws Lockknob See Figures 29,4 2gC Aligning the ARM for Cross CutsLock Lever Fronttable Socket Elevating Headscrews Handwheel Aligning Blade to Table AT 0 BevelSee Figures 30A 30D Indexcap BevelFramingsquare Yokelockhandle Squaring Blade to FenceSee Figures 31A 31C HexboltsSee Figures 32A-32C Noadjustment Needed BevelAdjustment GAP Paralleling Blade to TableAligning the RIP Scale Indicators IN-RIPSCALEONRIGHTSIDEOFARM RIP-SCALEINDICATORSee Figures 33A 33B Barrel Carriage Assembly SOCKETF.34 Installing Control CUT DeviceRIP Cuts Basic Operation of the Radial ARM SAWTypes of Cuts Cross CutsSwitch and Switch KEY Insertswitchkey Switchon Switchoff Causes of KickbackAvoiding Kickback Pushsticks Pushblocks Featherboard PushsticksPushblocks FeatnerboardsCarnage Lockknob Tableclamps Making a Cross CUTMaking a Miter CUT Making a Bevel CUT Making a Compound Cross CUT Beveledand Elevating HandwheelYoke Armpivotlatch Swwchyokelock Handle RIP CUT Hazards and Precautions Setting UP a RIP CUTElevating Handwheel Infeedfor Ripcutting Making a RIP CUT See Figure Review the Hazards and PrecautionsSupportlongworkpieces Making Other CutsSee Figures 48 Cutting Long WorkpiecesCuts NON-THROUGHMOTOR/ELECTRICAL General MaintenanceSolution Problem CauseProblem Remove handwheel clean and lubricate the shaft See Squaring the Blade to See Adjusting the ColumnTube in Assembly section AdjustmentssectionCause Solution Fence in AdjustmentssectionAssembly section Seefigure KEY Part Craftsmanradial ARM SAW- ModelnoKEY Part Number Description QuanFigureb Craftsman Radial ARM SAW Model no KEY Part NO.NUMBER63CRRFTSMRNRADIALSAW315.220381 Figurec Descripon Quan Parts List for Figure CFigured 67CRRFTSNHNRADIALSAW315220381 Parts List for Figure DFiguree Parts List for Figure E See Figure G Figuref71CRAFTSMANRADIALSAW315.220381 976287-001CRAFTSMANTABLESAW315,22038172 See Figure F Seefigureh73CRRPTSNRNRADIALSAW315.220381 Parts List for Figure GFigureh Descripon Ouan Parts List for Figure HFigurei Craftsmanradial ARM SAW Modelno Parts ListFigurej Craftsmanradial ARM SAW- Modelno ,220381 Parts List for Figure JFigurek Parts List for Figure K Parts Direct s