Craftsman 315.220381 owner manual RIP only Workpieces Longer than

Page 7

•SECURE THE SAW. Firmly belt the saw to the leg stand to keep the saw from tipping,walking, or sliding.

•DO NOT SET UP WORK WITH THE BLADE SPINNING. Keep the saw power off until you are ready to use it.

•RIP ONLY WORKPIECES LONGER THAN THE

BLADE'SDIAMETER. Never rip a piece of wood that is shorter than the diameter of the blade.

•NEVER LOWER AN UNLOCKED REVOLVING CUTTING TOOL. Always lock the carriage lock knob before lowering the blade.

•SHUT OFF THE POWER TO FREE A JAMMED GUARD. Press the switch off before puttingyour hands near the blade. Wait for the blade to stop, then free the guard.

•LOCK THE SAW BEFORE MOVING IT. Secure the radial arm with the arm lock knob. Secure the carriage with the carriage lock knob.

•POSITION THE WORKPIECE WITH THE FIN- ISHED SIDE DOWN. If the anti-kickbackpawls catch the wood to stop kickback, they could mar the top surface or cause splintering.

•POSlI_ION THE WORKPIECE SO NO ONE MUST STAND IN LINE WITH THE BLADE. if kickback or climb occurs, a helper, operator, or observer in the sawblade path could be seriously injured.

•POSITION THE CUT SO THE WASTE PART FALLS OFF. Never use a length stop on the free end of the workpiece. Never apply force to the free end or hold it while the sawblade is rotating.

_i, WARNING: In a ripcut, holding the cut-off edge behind the blade can cause the cut edges to

pinch, riskingkickback, tt could cause the blade to climb over the front edge of the wood and contact your hand.

•BEFORE STARTING EACH CUT, check that no play exists in the carriage. Be sure the arm, yoke

and bevel locks and clamps are tight. Verify the blade, all handles, blade washers, and blade nuts are secure.

•BEFORE MAKING A CUT, test the upper and lower blade guards for free movement up and down. Positionthe nose of the guard to just clear the workpiece.

•AVOID KICKBACK AND POSSIBLE INJURY by preventing heeling, grabbing, and pinching.

•BEFORE CUTTING, position and tighten the blade guard and anti-kickback pawls. Test the pawls to make sure they would stop kickback if it started. Keep the points sharp.

KEEP THE SAW BLADE PATH CLEAR. Position the saw to allow enough room on all sides so neither the operator nor a visitor stands in line with the sawblade.

•AVOID HEELING by adjusting the saw blade so it

exactly parallels the fence during rippingopera- tions.

•AVOID GRABBING in rip mode by keeping the saw blade correctly adjusted and by feeding the work from the infeed side (opposite the anti- kickback pawls).

•AVOID PINCHING by using a rivingknife and sharp saw blade. Keep the work positionedfirmly against the fence.

•USE IN-RIP WHENEVER POSSIBLE by position-

ing the work so the blade is between (inside) the column and the motor.

'NEVERADJUST GUARD, PAWLS, OR BLADE WITHOUT DISCONNECTING THE POWER.

Always turn off the switch and unplug the cord before freeing a jammed blade, tighteninga loose blade, or repositioningthe guard or pawls.

_k CAUTION: Do not turn the motor switch on and off rapidly. This can loosen the sawblade.

NEVER CUT MORE THAN ONE PIECE OF WOOD AT A TIME. The feed will be uneven and could cause the blade to pick up one or more pieces and cause serious injury.

TURN OFF SAW IF A STRANGE NOISE OR HEAVY VIBRATION OCCURS. Immediately turn off the saw, locate the source, and correct the problem before using the saw further.

POSITION THE CUT SO THE BLADE WILL NOT EXTEND BEYOND THE EDGE OF THE TABLE.

KEEP THE GUARDS IN PLACE AND THE WORK

SURFACE CLEAR DURING A CUT. Small objects or wood slivers can ricochet from the blade into the

fence and back toward the operator. If the blade loosens slivers, remove them with a stick, not your hand.

IN A RIP CUT, DO NOT LET GO OF THE WORK- PIECE UNTIL THE CUT IS COMPLETE. When the workpiece is fed intothe blade, push the workplace all the way past the blade.

7CRIIFI"SNIIN'RADIALSAW315.220381

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Ofess Ional Radial ARM SAWFull ONE Year Warranty on Craftsman Radial ARM SAW 28-29 Meaning Safety Alert Symbol SymbolAvoid Awkward Operations and Hand Be Sure the Blade Clears the Work RIP only Workpieces Longer than Grounding PIN Coverofgrounded Outletbox GroundinginstructionsSee Figures Changing VoltageBladearbor Gum BladeBevelAngleRAFTSNANRADIALSAW315,220381 Sawassemblyshownaspacked Cdef IIoII000 Level Io@CRE.ANTPARTS Inch Radii Arm SawAdvertencia See a KnowyourradialsawYoke 19IIRFTSMRNRADIALSAW315.220381 FeatureslistSee Figures 9A-9D Miterscale Armlockknob Yokepivotlatch RIPFigures 9A and 9B Dustguide Holddown MOTOR13/6.5AMP- Powersthebladeand isSee Figure lOB Assembly and Adjustments sections beforeTighten. See Figure I OA See Figure I OAElevating Shaft Handwheel Screw Starwasher Mounting SAW to LEG Stand Attaching Elevating HandwheelSee Figure SAW Base LEG Sawbase Hexbolt Flat Washer LockwasherCarriagearm Lockknob Installing the Yoke AssemblyArmviewedfrombelow Armlockknob ARM CapscrewsRemoving the Blade Blade Arbor Mounttablesupports UsingtheseholelocationsAttaching Table Supports Yokelock Handle Setting the ARM Lock KnobArmcap Motor Yokelock Handle Assembly See Figures 17,4and 17BBevel Bevel Setting the Bevel Lock LeverStarwasher Bevel BevellockleverinColumn ARM Tube Support Rear Coverscrews HEXBOLT2 HEXNUT2 Adjusting the Column TubeTightening the ARM and Column See Figures 20A 20DSilverblack Screws Columnsupport Elevation AdjustmentRotation Adjustment ColumntubeCarriagebearing Adjusting the Carriage BearingsEccentricscrew Wrench Graspandhold Carriagebearing Rightside Tablesupport Leveling Table SupportsSee Figures 22A and 22B Blade Wrenchat Front ArmlockknobHexnut Installing the Front TableSee Figures 23A 23C 23ASee Figures 25A 25C Leveling the Front TableReartablefence Spacertablefronttable Hole Clamp Bracket SquarenutBlade Rotation Hten WRENCH2 See Figures 27A 27C Carriage Speednut Installing RIP Scale IndicatorsSpring Carriage Screws Lockknob See Figures 29,4 2gC Aligning the ARM for Cross CutsLock Lever Fronttable Socket Elevating Headscrews Handwheel Aligning Blade to Table AT 0 BevelSee Figures 30A 30D Indexcap BevelFramingsquare Yokelockhandle Squaring Blade to FenceSee Figures 31A 31C HexboltsSee Figures 32A-32C Noadjustment Needed BevelAdjustment GAP Paralleling Blade to TableIN-RIPSCALEONRIGHTSIDEOFARM RIP-SCALEINDICATOR Aligning the RIP Scale IndicatorsSee Figures 33A 33B Barrel Carriage Assembly SOCKETF.34 Installing Control CUT DeviceRIP Cuts Basic Operation of the Radial ARM SAWTypes of Cuts Cross CutsInsertswitchkey Switchon Switchoff Causes of Kickback Switch and Switch KEYAvoiding Kickback Pushsticks Pushblocks Featherboard PushsticksPushblocks FeatnerboardsCarnage Lockknob Tableclamps Making a Cross CUTMaking a Miter CUT Making a Bevel CUT Beveledand Elevating Handwheel Making a Compound Cross CUTYoke Armpivotlatch Swwchyokelock Handle Setting UP a RIP CUT RIP CUT Hazards and PrecautionsElevating Handwheel Infeedfor Ripcutting Making a RIP CUT See Figure Review the Hazards and PrecautionsSupportlongworkpieces Making Other CutsSee Figures 48 Cutting Long WorkpiecesCuts NON-THROUGHMOTOR/ELECTRICAL General MaintenanceSolution Problem CauseProblem Remove handwheel clean and lubricate the shaft See Squaring the Blade to See Adjusting the ColumnTube in Assembly section AdjustmentssectionFence in Adjustmentssection Cause SolutionAssembly section Seefigure KEY Part Craftsmanradial ARM SAW- ModelnoKEY Part Number Description QuanFigureb KEY Part NO.NUMBER Craftsman Radial ARM SAW Model no63CRRFTSMRNRADIALSAW315.220381 Figurec Descripon Quan Parts List for Figure CFigured 67CRRFTSNHNRADIALSAW315220381 Parts List for Figure DFiguree Parts List for Figure E See Figure G Figuref71CRAFTSMANRADIALSAW315.220381 976287-001CRAFTSMANTABLESAW315,22038172 See Figure F Seefigureh73CRRPTSNRNRADIALSAW315.220381 Parts List for Figure GFigureh Descripon Ouan Parts List for Figure HFigurei Craftsmanradial ARM SAW Modelno Parts ListFigurej Craftsmanradial ARM SAW- Modelno ,220381 Parts List for Figure JFigurek Parts List for Figure K Parts Direct s
Top Page Image Contents