Haier 309292L important safety instructions HC Conversion Kit

Page 11

244919 HC Conversion Kit

Part No. 244919 Conversion Kit converts PRO Xs3 standard coating guns (Part Nos. 244400 and 244579) to high conductivity guns (244575 and 244576). For fur- ther instruction and parts, see manual 309453.

The kit is for use with fluids with low resistivity values.

WARNING

Pressurized Equipment Hazard

To reduce the risk of an injury, follow the Pressure Relief Procedure in your gun manual before installing this kit.

1.	Turn the ES ON/OFF valve OFF.
2.	Flush and relieve the pressure.
3.	Disconnect the fluid and air lines to the gun.

Installation

9.Slide the tube case (1e) onto the barrel inlet, over the o-ring (2b). The coiled tube (1a) will compress slightly.

10.Insert the end of the coiled tube (1a) into the bracket

(3). Make sure the ferrules (1c, 1b) seat on the bracket.

11.Secure the bracket by tightening the swivel (A). Tighten the nut (1d). Reinstall the exhaust tube (B) and clamp (C).

12.Reconnect the fluid and air lines to the gun.

	5	2
	5	1b
	2a	1b
	2a	1c
	2b	1d

4.	Remove the fluid tube and fittings.
5.	Remove the fluid inlet bracket.
6.	Install the new bracket (3) from the kit loosely. See
	FIG. 3.
7.	Place the spacer (5) in the barrel inlet. Apply Graco
	dielectric grease (4) to the o-rings (2a, 2b) and to
	both threads of the fluid fitting (2). Thread the fitting
	into the barrel inlet.
8.	Thread the nut (1d) onto the fitting (2). Make sure
	the ferrules (1c and 1b) are on the tube (1a) and are
	seated on the fitting (2) before tightening the nut
	(1d).

1e

1a

1e

1e 1e

FIG. 3: 244919 Conversion Kit

3

A

B

C

1e

ti10674a

309292L

11

Image 11

Contents PRO Xs3 and PRO Xs4 Air Spray Guns Table of Contents List of Models Toxic Fluid Hazard SymbolsFire, Explosion, and Electric Shock Hazard Pressurized Equipment Hazard Equipment Misuse HazardGun Overview IntroductionHow the Electrostatic Air Spray Gun Works Flammable or Toxic Vapor Hazard InstallationInstall the System Ventilate the Spray BoothTypical Installation Key Supply Hose Connect the Air LineConnect the Exhaust Tube Electric Shock HazardOrifice Size Connect the Fluid LineFilter the Fluid Select a Fluid Nozzle and Air Cap244919 Conversion Kit HC Conversion KitGrounding Check Gun Grounding Check Electrical GroundingCheck Fluid Viscosity Check Fluid ResistivityKV Guns Low Voltage Adjustment Smart Guns OnlyOperation Flush the Spray Gun MaintenanceHang the gun from its hook, with the nozzle pointing down Test Gun Resistance Electrical TestsTest Power Supply Resistance Test Power Supply ResistanceTest Electrode Resistance Test Electrode ResistanceSpray Pattern Troubleshooting TroubleshootingGun Operation Troubleshooting See Check Fluid Resistivity on Electrical TroubleshootingSee Test Gun Resistance on Repair Pressure Relief ProcedurePrepare the Gun for Service Air Cap/Nozzle Replacement Electrode Replacement Electrode ReplacementFluid Packing Removal Fluid Packing RemovalPacking Rod Packing Rod RepairBarrel Removal Barrel InstallationPower Supply Power Supply Removal and ReplacementFluid Tube Removal Replacement PRO Xs4 Guns Only Turbine Alternator Removal and ReplacementFan Air Adjustment Valve Fan Air Adjustment Valve RepairAir Valve Repair Fluid Adjustment Valve RepairES ON/OFF Valve Repair Atomizing Air Restrictor Valve Removal and ReplacementParts Fluid Tube Model Ref. No Alternator Ref. No Fan Adjustment ValveRef. No Packing Rod Ref. No ES ON/OFF Valve Description Qty Description Qty 51 Ref Ref. No ES ON/OFF Valve Ref. No Packing Rod Part No. Description Qty Part No. Description Qty Fluid Line Accessories AccessoriesAir Line Accessories Miscellaneous Accessories Gun AccessoriesCategory Data Technical DataTechnical Data 309292L Toll Free Graco Standard WarrantyGraco Information