Hitachi DV 14DV, DV 18DV Before USE, Disconnect battery charger from the receptacle

Page 15

English

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5.Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

●When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

●If the battery is rechraged when it is warm due to battery use or exposure to sunlight, the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

●When the pilot lamp flickers in red (at 0.2–second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1)Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

(2)Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

15

Image 15

Contents Avertissement AdvertenciaVariable speed Contents Meanings of Signal Words Important Safety InformationGeneral Safety Rules for ALL Battery Operated Tools SafetyEnglish Specific Safety Rules and Symbols Carefully handle power tools Never use a tool which is defective or operating abnormallyDo not wipe plastic parts with solvent Important Safety Instructions for Battery Charger English Make Them Available to Other Users Owners of this Tool Disposal of the Exhausted BatteryCordless Hammer Drill DV14DV and DV18DV Functional DescriptionModel Name of PartsCordless Hammer Drill SpecificationsBattery Charger UC24YFA or UC24YF Battery ChargerApplications Assembly and OperationRemoval and Installation Method of Battery Insert the plug of battery charger into the receptacleCharging Insert the battery to the battery chargerDisconnect battery charger from the receptacle Remove the battery from the battery chargerBefore USE Mounting and dismounting the bit OperationConfirm the cap position see Fig Change rotation speedRotation to Hammer changeover Tightening torque adjustmentFor drilling into brick Scope and Suggestions for UsesHOW to Select Tightening Torque Maintenance and Inspection Standard Accessories AccessoriesBattery EB14BFor DV14DV Battery EB1820, EB18BFor DV18DV Optional ACCESSORIES.....sold separatelySignification DES Mots D’AVERTISSEMENT Informations Importantes DE SécuritéSecurite Conserver CES InstructionsAvertissement Lire et coxmprendre toutes les instructions Avertissement Regles DE Securite Specifiques ET Symboles Ne pas essuyer les parties en plastique avec du solvant Manipuler l’outil motorisé avec précautionIntensité nominale d’entrée CA ampères Français Mise AU Rebut D’UNE Batterie Usée Marteau perforateur à batterie DV14DV et DV18DV Description FonctionnelleModele NOM DES PartiesChargeur de batterie UC24YFA ou UC24YF Marteau perforateur à batterieChargeur de batterie Brancher la fiche du chargeur de batterie dans la prise Méthode DE Retrait ET D’INSTALLATION DE LA BatterieUtilisations Méthode DE RechargeRecharge Insérer la batterie dans le chargeur de batterieRetirer la batterie du chargeur de batterie Débrancher le chargeur de batterie de la prisePose et dépose du foret Vérifiez si la batterie a été correctement installéeAvant L’UTILISATION UtilisationChangement de vitesse de rotation Vérifiez la direction de rotationCommutation rotation sur percussion Vérification de la position du capuchon. Voir FigPerçage de briques Réglage du couple de serrageSélection DU Couple DE Serrage Plage D’UTILISATION ET SuggestionsFrançais Entretien ET Inspection Accessoires Standard AccessoiresAccessoires EN OPTION.....vendus séparément Significado DE LAS Palabras DE Señalización Información Importante Sobre SeguridadSeguridad Guarde Estas InstruccionesAdvertencia Lea y entienda todas las instrucciones Advertencia Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadNo toque Nunca las piezas móviles Utilice la herramienta correctaNo limpie las partes de plástico con disolvente Maneje con cuidado las herramientas eléctricas100 150 Español Eliminación DE LAS Baterías Agotadas Martillo roto-percutor a batería DV14DV Y DV18DV Descripción FuncionalModelo NomenclaturaCargador de baterías EspecificacionesCargador de baterías UC24YFA o UC24YF Martillo roto-percutor a bateríaMétodo DE Carga Montaje Y OperaciónAplicaciones Método DE Extracción E Instalación DE LA BateríaCarga Inserte la batería en el cargador de bateríasDesconecte el cargador de baterías del tomacorriente Extraiga la batería del cargador de bateríasForma de hacer que las baterías duren más Confirmar que la batería está puesta correctamente Antes DE LA UtilizaciónOperación Montaje y desmontaje de la brocaCambio de velocidad de rotación Examinar la dirección de rotaciónConfirmar la posición de la cubierta Ver la Fig Cambio de rotación a percusiónAjuste del par de apriete Para taladrar en ladrillo Alcance Y Sugerencias Para LA UtilizaciónForma DE Seleccionar EL PAR DE Apriete Mantenimiento E Inspección Accesorios Estándar Accesorios OPCIONALES.....de venta por separado Page Hitachi Koki Canada Co