Dremel 335 warranty Operating Instructions, Under a router or saw table Inserting the Router Bit

Page 4

DM 2610920458 2-04 2/19/04 12:24 PM Page 4

Operating Instructions

ATTACHMENT FOR USE WITH DREMEL HIGH SPEED ROTARY TOOL MODELS 275, 285, 395, & 398.

ATTENTION: This attachment will convert Dremel Rotary Tool to a Plunge Router for freehand routing, edging, grooving, and

circular cuts. The router attachment comes assembled ready for freehand or pilot bit routing.

!WARNING This Router Attachment is not intended for use

under a router or saw table.

Inserting the Router Bit

The router bits are held in the tool by a collet system. The bit may be installed before or after the rotary tool is installed in the attachment.

1.Depress and hold the shaft lock button while rotating the collet nut and shaft. Continue to rotate the collet nut and shaft until the lock engages and holds the shaft (Fig. 4).

2.Use the wrench from your Dremel Rotary Tool and turn the collet nut counter- clockwise to loosen it.

3.Release the shaft lock button.

4.Insert the router bit into the collet as deep as possible to ensure proper grip- ping of the bit and to minimize run out. Do not insert the bit so far that bit flutes touch the collet or collet nut to avoid chipping or cracking the bit.

NOTE: Never place the tool with bit protruding through base on top of bench or work surface. Lay the tool on its side or retract the bit before setting on bench or work surface. Protruding cutting bit may cause tool to jump.

5.Re-engage the shaft lock button and tighten the collet nut; first by hand, then using the wrench until bit is held securely.

FIG. 4

Shaft Lock

Button

Collet Nut

Collet Nut

Wrench

Base

4

Image 4

Contents Safety Assembly Power Tool Safety Rules Safety Rules for RoutersOperating Controls Assembling Plunge Router Attachment to your ToolUnder a router or saw table Inserting the Router Bit Operating InstructionsShaft Lock Button Collet Nut Wrench Base Adjusting Routing Depth Lower Adjustment NutRelease Button Hand Grip 1st Routing Depth StopRelease button Feeding the Router Rate Of FeedEdge Forming Router Feed DirectionTool Lubrication Assembling the Edge GuideInstallation Edge GuideRouting with Edge Guide Mounting Blocks Edge Guide Routing Arcs and CirclesBushing TemplatesPlug Part Dremel Parts DiagramPart Description Dremel Limited Warranty Dremel Service Center Twenty-First Street Racine, WisconsinDM 2610920458 2-04 2/19/04 1224 PM Règles de sécurité concernant les toupies Règles de Sécurité GénéralesConservez CES Instructions Commandes Poignée fixeGuide parallèle Guide de CercleConsignes de fonctionnement Écrou de réglage Inférieur Bouton de Déblocage PoignéeProfondeur de toupillage Manière à amener la cote X à la première proBouton de déblocage Mouvement d’avance Vitesse d’avanceToupillage de chants Sens d’avance de la défonceuseAssemblage du guide parallèle Lubrification de l’outilVis de réglage de profondeur Installation Guide parallèleToupillage avec le guide parallèle Clou de finition Guide parallèleBagues DE Guidage GabaritsToupillage À Main Levée No de Schéma des pièces DremelNo de Description Réf Pièce Dremel Service Center Twenty-First Street Racine, Wisconsin Garantie limitée de DremelÉTATS-UNIS CanadaDM 2610920458 2-04 2/19/04 1224 PM Normas de seguridad para fresadoras Normas de seguridad para herramientas mecánicasConserve Estas Instrucciones Controles de utilización Botón de fijación Del eje Instrucciones de utilizaciónBase Ajuste de la profundidad de fresado Tuerca de Ajuste inferiorTope de ProfundidadBotón de suelta Avance de la fresadora Velocidad de avanceConformado de bordes Sentido de avance de la fresadoraLubricación de las herramientas Montaje de la guía de bordeTornillo de ajuste de profundidad De guíaGuía de borde InstalaciónFresado con la guía de borde Bloques de MontajePlantillas Casquillos DE GuíaCasquillo de guía Base Patrón de Plantilla Guía ExcentricidadDescripción Diagrama de piezas DremelPieza Garantía limitada Dremel Estados UnidosDM 2610920458 2-04 2/19/04 1224 PM Remarques Notas