Dremel 335 warranty Tool Lubrication, Assembling the Edge Guide

Page 7

DM 2610920458 2-04 2/19/04 12:24 PM Page 7

Tool Lubrication

Periodic cleaning and lubrication of guide posts will keep plunge action smooth.

Depress and lock plunge router and evenly apply a light lubricant (i.e. petroleum jelly, cooking oil) to upper portion of guide posts.

Assembling the Edge Guide

For edge guide use, assemble guide rods into tool holder assembly and secure using (2) #10-24 square nuts and (2) guide rod knobs (Fig. 11).

Square nut will slide in slots above the guide rods. Guide rod knobs are assembled from the top through holes down through nuts, and against the rods. Fasten edge guide to guide rods using edge guide knobs, and hex head nuts.

Locate hex head nuts underneath edge guide and fasten with edge guide knob on top surface of edge guide. Slide edge guide

assembly on guide rods as shown. Set edge guide at desired distance from cutter and tighten edge guide knobs. (See Fig. 11 )

Edge guide is used for shaping edges, cut- ting rabbets, dadoes, mortise, tongues, grooves, slots, and chamfers. Remember to feed so the cutter tends to pull the edge guide against the wood. A consistent feed rate gives a smooth cut.

In general, several shallow cuts should be used when a deep groove is desired. Maximum depth of cut will vary depending on material used. Do not over feed to an amount that the motor is noticeably slowed.

	Depth Adjustment	Guide Rod Knob
FIG. 11	Screw
FIG. 11

Edge Guide Knob

Square Nuts

Guide Rods

Edge Guide

Finishing Nail

Circle Guide Hex Head Nuts

7

Image 7

Contents Safety Assembly Safety Rules for Routers Power Tool Safety RulesAssembling Plunge Router Attachment to your Tool Operating ControlsUnder a router or saw table Inserting the Router Bit Operating InstructionsShaft Lock Button Collet Nut Wrench Base 1st Routing Depth Stop Adjusting Routing DepthLower Adjustment Nut Release Button Hand GripRouter Feed Direction Release button Feeding the RouterRate Of Feed Edge FormingAssembling the Edge Guide Tool LubricationMounting Blocks Edge Guide Routing Arcs and Circles InstallationEdge Guide Routing with Edge GuideBushing TemplatesPlug Part Dremel Parts DiagramPart Description Dremel Service Center Twenty-First Street Racine, Wisconsin Dremel Limited WarrantyDM 2610920458 2-04 2/19/04 1224 PM Règles de sécurité concernant les toupies Règles de Sécurité GénéralesConservez CES Instructions Guide de Cercle CommandesPoignée fixe Guide parallèleConsignes de fonctionnement Manière à amener la cote X à la première pro Écrou de réglage InférieurBouton de Déblocage Poignée Profondeur de toupillageSens d’avance de la défonceuse Bouton de déblocage Mouvement d’avanceVitesse d’avance Toupillage de chantsAssemblage du guide parallèle Lubrification de l’outilVis de réglage de profondeur Clou de finition Guide parallèle InstallationGuide parallèle Toupillage avec le guide parallèleBagues DE Guidage GabaritsToupillage À Main Levée No de Schéma des pièces DremelNo de Description Réf Pièce Canada Dremel Service Center Twenty-First Street Racine, WisconsinGarantie limitée de Dremel ÉTATS-UNISDM 2610920458 2-04 2/19/04 1224 PM Normas de seguridad para fresadoras Normas de seguridad para herramientas mecánicasConserve Estas Instrucciones Controles de utilización Botón de fijación Del eje Instrucciones de utilizaciónBase Profundidad Ajuste de la profundidad de fresadoTuerca de Ajuste inferior Tope deSentido de avance de la fresadora Botón de suelta Avance de la fresadoraVelocidad de avance Conformado de bordesDe guía Lubricación de las herramientasMontaje de la guía de borde Tornillo de ajuste de profundidadBloques de Montaje Guía de bordeInstalación Fresado con la guía de bordeExcentricidad PlantillasCasquillos DE Guía Casquillo de guía Base Patrón de Plantilla GuíaDescripción Diagrama de piezas DremelPieza Estados Unidos Garantía limitada DremelDM 2610920458 2-04 2/19/04 1224 PM Remarques Notas