Dremel 220 owner manual Operation, Installing Rotary Tool

Page 6
Shaft Lock Button
Figure 2. Loosening/Tightening Collet 4. Insert the drill bit into the collet as deep
as possible to ensure proper gripping of the bit and to minimize run out. Do not insert the bit so far that the flutes touch the collet or collet nut to avoid chipping or cracking the bit.
5. Re-engage the shaft lock button and tight- en the collet nut; first by hand, then using the wrench until bit is held securely.

DM 2610921728 8-05E 8/23/05 9:15 AM Page 6

Operation

IMPORTANT! Work Station is for use with only one tool at time. Do not hang a tool on hanger assembly when another tool is mounted in the press.

The Crow’s Nest tool storage will hold the fol- lowing tools:

• Drill bit set (Model 628 or 631)

• Rotary tool wrench

• Mounting wrench

• Bits with shank size less than or equal to 1/8"

• Rotary tool collets (Models 480, 481, 482, 483)

NOTE: The drill bits are held in the tool by a collet system. The bit may be installed before or after the rotary tool is installed in the drill press.

1. Depress and hold the shaft lock button while rotating the collet nut and shaft. Continue to rotate the collet nut and shaft until the lock engages and holds the shaft (Figure 2).

2. Use the wrench from your Dremel Rotary Tool and turn the collet nut coun- terclockwise to loosen it.

3. Release the shaft lock button

Cord should be positioned to the side when drill press is used.

Clamp Nut

Figure 3. Installing Rotary Tool

6

Image 6
Contents Manual Contents Work Station ModelWork Area Power Tool Safety RulesSave These Instructions Personal Safety Tool Use and CareSafety Rules for Drill Press ServiceAssembly Attachment for USE with DremelWork Station 220 Components Installing Rotary Tool OperationSetting Depth and Height Adjustments Helpful hints Making optional hold down clamps for Your Work StationDremel Limited Warranty Canada OutsideContinental United States Parts Diagram 33 3Ref. Part No Description DM 2610921728 8-05E 8/23/05 915 AM Mode demploi Table des MatièresRègles de Sécurité Générales Aire de TravailSécurité des Personnes Consignes de Sécurité pour les outils Électroportatifs Utilisation et Entretien des OutilsSécurité Pensez À LAILS Rotatifs Dremel Modeles CET Accessoire Convient AUX OUTAssemblage 285, 295, 300, 398, 400, 780 ETPoste de Travail Modèle 220 Composant Utilisation Montage de loutil RotatifUtilisation suite Réglage de la Profondeur et de la HauteurConseils Utiles Brides de Pièces Non fourniesFabrication de Brides En Option Garantie limitée de Dremel Canada EN Dehors DES États AméricainsContinentaux Schéma des pièces Remarques Manual del Usuario Contenido del ManualSeguridad Eléctrica Normas de seguridad para Herramientas MecánicasArea de Trabajo Seguridad PersonalNormas de Seguridad para el Taladro de Columna Utilización y Cuidado de las HerramientasNormas de Seguridad para el Taladro de Columna continuación LOS Modelos Giratorios Dremel MontajeAditamento Para Utilizarse CON 275, 285, 295, 300, 398, 400, 780 YFigura 1. Componentes de la Estación de Trabajo Utilización Figura 3. Instalación de la Herramienta GiratoriaUtilización continuación Consejos útiles Figura 7. Pieza de trabajo redondaUtilización continuación Garantía Limitada de Dremel Canadá Fuera DELOS Estados Unidos Continentales 2726 3334 Diagrama de piezas56a 86a Descripción