Bostitch BTE140K instruction manual Specific Safety Rules, Always Wear Certified Safety Equipment

Page 3

f)Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4)Power tool use and care

a)Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b)Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c)Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d)Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e)Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f)Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g)Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5)Service

a)Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Specific Safety Rules

Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.

Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Use clamps or another practical way to secure and support the work piece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

Keep your hair, clothing, and gloves away from air vents. Air vents often cover moving parts in which these items can be caught.

Hammer bits and tools get hot during operation. Wear gloves when touching them.

Hold tool firmly with two hands. Use auxiliary handle if provided. Loss of control can cause personal injury.

Wear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly. Flying particles can cause permanent eye damage. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if drilling operation is dusty.

ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paints,

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

3

Image 3
Contents BTE140 Work Area Safety Safety Guidelines DefinitionsAlways Wear Certified Safety Equipment Specific Safety RulesFUNCTIONAL DESCRIPTION Attaching the side handle figure C Safety Warnings and Instructions DrillsDrilling In Wood Drilling in Masonry Shift drill into hammer modeDrilling Selecting the direction of rotationAccessories TroubleshootingMaintenance Replacement Parts Service and RepairsThree Year Limited Warranty Lignes directrices en matière de sécurité définitions Juego DeTaladro Percutor De 12,7 Mm 1/2 PulgadaPage Consignes de sécurité particulières Toujours Porter UN Équipement DE Protection Homologué SymbolesAssemblage Insérer une mèche ou un autre accessoire fig. DAvertissements de sécurité et directives perceuses AvertissementSélecteur à double marche fig. F Sélection du mode perceuse fig. EFonctionnement Sélection du sens de rotationPerçage du métal Mode perçageMise en marche et arrêt Perçage du boisPièces DE Rechange Entretien ET Réparation Capacités Maximales RecommandéesDépannage EntretienAccessoires Remplacement DES Étiquettes D’AVERTISSEMENTGarantie Limitée DE Trois ANS Pautas DE SEGURIDAD/DEFINICIONES Page Normas de seguridad específicas Símbolos Acoplamiento del mango lateral fig. C Instrucciones y advertencias de seguridad TaladrosAdvertencia EnsamblajeSelector de dos engranajes fig. F Instrucciones de operaciónSelección del modo de taladrado fig. E Selección de la dirección de RotaciónTaladrado en madera Ajuste de la profundidad de perforaciónEncendido y apagado TaladradoCapacidades Máximas Recomendadas Detección de problemasMantenimiento Piezas DE RepuestoReemplazo DE LAS Etiquetas DE Advertencia Mantenimiento Y ReparacionesAccesorios Garantía Limitada DE Tres AnosPage Catalog Numbers BTE140 Form June