Hobart Welding Products OM-486 manual Changing Engine Oil, Oil Filter, And Fuel Filter, Full

Page 29

7-5. Changing Engine Oil, Oil Filter, And Fuel Filter

Full

YStop engine and let cool.

1Oil Drain Valve

21/2 ID x 12 in Hose

3Oil Filter

Change engine oil and filter accord- ing to engine manual.

YClose valve and valve cap before adding oil and run- ning engine.

Fill crankcase with new oil to full mark on dipstick (see Section 7-2).

4Fuel Filter

5Fuel Line

Replace line if cracked or worn. Install new filter. Wipe up any spilled fuel.

Start engine, and check for fuel leaks.

YStop engine, tighten connec- tions as necessary, and wipe up fuel.

Tools Needed:

Ref. ST-801 942-C / ST-800 395-B / Ref. ST-189 925-A / S-0842

OM-486 Page 25

Image 29

Contents Description OM-486Processes From Hobart to You Table of Contents Page Arc Welding Hazards Symbol UsageElectric Shock can kill ARC Rays can burn eyes and skinEngine Hazards Moving Parts can cause injury Battery Explosion can BlindEngine Exhaust Gases can kill Engine Heat can cause fireEMF Information Principal Safety StandardsRadiation can cause interference ARC Welding can cause interferenceConsignes DE SÉ Curité Lire Avant Utilisation Signification des symbolesUN Choc É Lectrique peut tuer LES Fumé ES ET LES GAZ peuvent ê tre dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un in- cendie ou une explosionDES PIÈ CES Chaudes peuvent provoquer des brû lures graves LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peut DES Organes Mobiles peuvent provoquer des blessuresLA Chaleur DU Moteur peut pro- voquer un incendie LA Chute DE L’APPAREIL peut blesserInformation sur les champs é lectromagné tiques Principales normes de sé curitéLE Soudage À L’ARC risque de provoquer des interfé rences Consignes relatives aux stimulateurs cardiaquesSymbol Definitions SpecificationsWeld, Power, And Engine Specifications DefinitionsFuel Consumption Dimensions, Weights, and Operating AnglesDimensions Duty Cycle Auxiliary Power CurveExceeding duty cycle can damage unit and void warranty CV/DC Mode CC/DC ModeCC/AC Mode Volt-Ampere CurvesEngine Prestart Checks InstallationInstalling Welding Generator Do not overfill battery cells Activating The Dry Charge Battery If ApplicableRead and follow all instruc ChargerInstalling Exhaust Pipe Connecting The BatteryConnecting To Weld Output Terminals Connect negative cable lastRemote 14 Receptacle Information Selecting Weld Cable Sizes100 ft 30 m Or Less 10 100% Duty CycleStop engine Adjusting MIG Weld Puddle ConsistencyTo wet out weld puddle To stiffen weld puddleDo not switch under load DC Polarity/AC SwitchRemote Amperage/Voltage Switch Operating Welding GeneratorRemote Amperage/Voltage Control Weld Current 120 240 Auxiliary Power Receptacles And Circuit BreakersOperating Auxiliary Equipment Gfci Receptacle Option Optional Auxiliary Power ReceptaclesMaintenance and Troubleshooting Maintenance Label Stop engine and let cool Servicing Air CleanerServicing Optional Spark Arrestor Changing Engine Oil, Oil Filter, And Fuel Filter Weld/Power Speed Adjustment Adjusting Engine SpeedIdle Speed Adjustment Overload Protection TroubleshootingWelding Trouble RemedyCheck and clean air cleaner as necessary see Section Low weld output Check control settingsCheck and adjust engine speed see Section See engine manualCheck receptacle wiring and connections Auxiliary PowerEngine Check governor according to engine manualCircuit Diagram For Welding Generator Electrical DiagramST-190 578-B Grounding Generator To Truck Or Trailer Frame Auxiliary Power GuidelinesSelecting Equipment How Much Power Does Equipment Require? Grounding When Supplying Building SystemsEarth ground if supplying Amperes x Volts = WattsApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP x240 120 Ground Typical Connections To Supply Standby PowerCurrent Load Watts Amperes Selecting Extension Cord Use Shortest Cord Possible24-Fig Parts ListMain Assembly Dia Part Description Mkgs Quantity Panel, Front w/Components Panel, Front w/Components -1 Item Generator -1 Item Page Page Page Support ServiceCall Contact your Distributor forHobart Welding Products