DeWalt D26411 instruction manual Switching On and Off Fig, Stripping paint, Prior to Operation

Page 9

OPERATION

WARNING: Make sure the nozzle ALWAYS points away from you and any bystanders.

WARNING: DO NOT drop anything into the nozzle. WARNING: Use only one hand to hold the tool as shown in

Figure 2. Do not place your other hand over the air vents (Fig. 3).

FIG. 2

FIG. 3

FIG. 4

A

English

PRIOR TO OPERATION

1.Attach the correct accessory recommended for the application.

2.Turn the air temperature adjustment knob (D) to desired air temperature.

Switching On and Off (Fig. 4)

1.Push the on/off switch (A) to the desired air flow settings:

I:240 liter/min [122–752ºF (50˚C-400˚C)]

A low air flow to heat up the workpiece slowly.

II:450 liter/min [122–1112ºF (50˚C-600˚C)]

A high air flow to heat up the workpiece quickly.

2.To turn the tool off, push the on/off switch (A) to position O. Disconnect the tool from the power source and let the tool cool down before moving or storing it.

Stripping paint

WARNING: Refer to Important Notice under Additional Safety Instructions for Heat Guns before using the tool remove paint.

WARNING: Do not strip metal window frames as the heat may crack the glass.

•When striping other window frames, use the glass protection nozzle.

•To prevent igniting the surface, do not keep the tool directed at one spot too long.

•Avoid collecting paint on the scraper accessory, as it may ignite. If necessary, carefully remove paint debris from the scraper accessory using a knife.

1.Attach the appropriate accessory.

2.Turn the air temperature adjustment knob (D) to high.

3.Turn the tool on by selecting the desired air flow.

4.Direct the hot air onto the paint to be removed.

Best results will be achieved if the heat gun is moved slowly, but CONSTANTLY, from side to side to evenly distribute heat. DO NOT LINGER OR PAUSE IN ONE SPOT.

7

Image 9

Contents D26411 Page Important Safety Instructions Definitions Safety GuidelinesWork Area Safety Electrical SafetyPersonal Safety Additional Safety Instructions for Heat GunsService Tool USE and CareVoltage Volts Total length of cord in meters m Important Notice AS YOU PRACTICE, Observe the Following Procedures for SafetySave These Instructions for Future USE SpecificationsDescription Fig Intended USESetting the Air Temperature Fig Assembly and AdjustmentsSetting Applications Attach the Correct AccessoryOperation Switching On and Off FigStripping paint Prior to OperationMaintenance Accessories Instrucciones de seguridad importantes Definiciones Normas De seguridadLEA Estas Instrucciones Seguridad DEL Área DE TrabajoUSO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalNo USE Esta Herramienta Como Secadora DE Pelo MantenimientoTénsion Volts Longitud del cable en metros m Nota Importante SI Está Removiendo PINTURA, Siempre Siga Estas Pautas Guarde Estas Instrucciones Para SU Futura ReferenciaDescripción FIG EspecificacionesMontaje Y Ajustes Para fijar la temperatura del aire FigEncendido y apagado Fig FuncionamientoUSE EL Accesorio Correcto Antes DE Operar LA HerramientaRemoción de pintura Uso estacionario FigControl constante de calor protección de sobrecarga Mantenimiento Instruções de Segurança Importantes Definições Diretrizes de SegurançaLeia Estas Instruções Guarde Estas InstruçõesUSO E Cuidados DA Ferramenta Segurança PessoalNunca USE Esta Ferramenta Como Secador DE Cabelo ReparosTensão Volts Comprimento do cabo de Faixa de Corrente SecçãoCabo de Extensão Nominal AO PRATICAR, Siga OS Seguintes Procedimentos DE Segurança Aviso ImportanteEspecificações Guarde Estas Instruções Para USO FuturoMontagem E Ajustes Descrição FigComo ajustar a temperatura do ar Fig USO Devido DA FerramentaComo ligar e desligar o aparelho Fig Como Usar O AparelhoComo Prender O Acessório Correto Ícone Descrição UsoComo usar seu aparelho como ferramenta fixa Fig Como remover tintaControle de calor constante proteção contra sobrecarga Anel para suspender a ferramenta FigManutenção Período de resfriamentoLubrificação LimpezaCopyright @ 2008 D Ewalt