Conair UGH016/0500 manual TIC Control Features, Display

Page 34

TIC CONTROL FEATURES

The TIC control lets you view the status of the chiller and change settings.

System lights

Light when compressor, pump or alarm activates

Display

4-digit LED screen shows To Process tem- perature, new settings and run modes. Indicator light shows hot gas unloading.

System buttons

Quick text

Control buttons

Press to start and stop

Follow steps to

Press to access menus,

chiller and to silence

change setpoints

enter data, and to scroll

optional audible alarm

Unloading indicator

Lights when the hot gas bypass is unloading.

Menu Access button

Press to enter or change setpoint, to exit the menu, and to index to the next menu.

Raise button

Increases values, hold for fast-step progression.

4-Digit LED display

Shows status, settings and run modes.

Mode/Enter button

Press to enter parameter selec- tions, access operating modes, silence alarms, and index through menu items.

Lower button

Decreases values; hold for fast-step progression.

4-2

OPERATION

Series 1 Portable Chillers, TIC Control

UGH016/0500

Image 34

Contents Portable Chillers Conair GROUP, INC Table of Contents IntroductionParts and Diagrams . . . . . . . . . . . .P/D-1 Introduction HOW Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description What is Portable CHILLER? Cooling load TemperatureTypical Applications LocationHOW IT Works WATER-COOLED Portable Chiller Process circulationHOW IT Works HOW IT Works AIR-COOLED Portable Chiller HOW IT Works AIR-COOLED Portable ChillerChiller Features Water-cooled ModelsPortable Chiller Features Air-cooled ModelsSpecifications ModelSpecifications Pump Curves Installation Unpacking the Boxes UGH016/0500 Series 1 Portable Chillers, TIC Control Grounded power source Preparing for InstallationAvailable water source Wrap threads with Mylar or Teflon tape Making Process Plumbing ConnectionsConnect the To Process valve and tubing on Open the Fill/Drain valve and fill chiller Filling the ChillerAttach water hose to Fill/Drain valve Close the Fill/Drain valveChange the minimum operating temperature Check the coolant levelChecking Refrigerant Charge Connecting Main Power Source Connect the ground wire to grounding lugChecking Electrical Connections Close the electrical enclosure Turn on main power sourceOpen electrical enclosure Check the rotation of the pump Initially Starting ChillerPress the Start Chiller button Check the compressorStopping the Chiller Operation TIC Control Features DisplayBefore Starting Check that the casters are lockedStarting Stopping Chiller Press Menu button once Changing SettingsChanging Setpoint Temperature Press the Up/Down arrowsChanging Temperature Scale Changing to Auto Tune ModePress Enter button Changing Auto Tune ModeUse the Up/Down arrows to change Apply a load to the ChillerSetting the to Process LOW Limit Maintenance Maintenance Features UGH016/0500 Series 1 Portable Chillers, TIC Control Inspecting the condenser coil for debris Preventative Maintenance ScheduleChecking electrical connections Checking refrigerant site glassInspecting cooling water treatment system CleaningCleaning process fluid strainer Inspecting condenserCheck the refrigerant charge through the sight glass Cleaning Evaporator or WATER-COOLED Condenser Inspect the coils Cleaning AIR-COOLED CondenserCoil cleaner Use a flashlight to check between coil surfacesBe sure the main power is disconnected Locate the fill port on the back of the chiller Disconnect and lockout power to the chillerChecking Reservoir Level Refill the reservoirTroubleshooting Before Beginning FEW Words of CautionIdentifying Cause Problem DAY TimeAnswering AN Alarm Pump Compressor Alarm Condition Description StatusPower is not reaching the chiller Control ProblemsThere is a problem with the control panel Symptom Possible cause Solution Input voltage is incorrect There is a phase lossMechanical Conditions Failed Level switchWater level in tank is low Low Pump Overload Overload set incorrectly. pump and compres Faulty contactorFaulty overload module Low supply voltageAlarm Possible cause Overload set incorrectlyClogged/dirty air-cooled Compressor discharge Valve closedFaulty Failed flow switchPressure switch is No or low flow with aCompressor failed Contact Conair Service Leads are backwardsReplace the switches as needed Checking Replacing SwitchesCheck the switch Slide the top of the switch housing over untilReplacing the Contactor Disconnect the wiring from the contactorReconnect the wiring and reconnect power Remove the contactor by snapping offChecking and Replacing Contact Conair Service for the temperature Replacing Temperature ControllerSlide the new controller in until Replacing Overload Modules Reconnect wires and leadsRestore power to the chiller Rating of compressor, fan or pumpReplacing Fuses Remove and replace fusesRemoving Pump Components Remove the pump assemblyInspect, clean, and replace pump parts Open the drain/fill valveDAY Time Checking Pressure SwitchesLocate the pressure switch Check the connectionsCheck the continuity within the switch Make sure it corresponds to the following conditionsPage WE’RE Here to Help From outside the United States, call2SERVICE Information Warranty Information Maintenance LOG Date Maintenance ItemPage Pressure Tables Appendix C-2Control Settings Display Parameter Description Setting UnitsPage Parts & Diagrams Recommended Spare Parts Part Number DescriptionSpare Parts P/D-3 4SPARE Parts Spare Parts P/D-5 6SPARE Parts