Conair Portable Chillers Series 1Water-Cooled (W1) and Air-Cooled Models (A1) withTIC Control

Page 55

Look here if the control panel is not lit, or if the power is on and the Portable Chiller will not run.

CONTROL PROBLEMS

Symptom

Possible cause

Solution

The control is not lit and the chiller is not working.

Power is not reaching the chiller.

❐Check the power cord and plug. Make sure the cord and plug are properly connected.

❐Make sure the main discon- nect switch is on.

❐Check fuses and breakers. Replace or reset as required.

The correct power is not	Check the voltage specification
reaching the unit	on the chiller nameplate.

There is a problem with the TIC control.

❐Check fuses and replace as needed.

❐Check the power to the tem- perature controller. Reconnect or replace as needed.

❐Check the TIC indicator lights and replace as needed.

There is a problem with the control panel.

The control panel may have failed. Contact Conair Service.

UGH016/0500

Series 1 Portable Chillers, TIC Control

TROUBLESHOOTING 6-5

Image 55

Contents Portable Chillers Conair GROUP, INC Introduction Table of ContentsParts and Diagrams . . . . . . . . . . . .P/D-1 Introduction HOW Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Page Description What is Portable CHILLER? Location TemperatureTypical Applications Cooling loadProcess circulation HOW IT Works WATER-COOLED Portable ChillerHOW IT Works HOW IT Works AIR-COOLED Portable Chiller AIR-COOLED Portable Chiller HOW IT WorksWater-cooled Models Chiller FeaturesAir-cooled Models Portable Chiller FeaturesModel SpecificationsSpecifications Pump Curves Installation Unpacking the Boxes UGH016/0500 Series 1 Portable Chillers, TIC Control Grounded power source Preparing for InstallationAvailable water source Wrap threads with Mylar or Teflon tape Making Process Plumbing ConnectionsConnect the To Process valve and tubing on Close the Fill/Drain valve Filling the ChillerAttach water hose to Fill/Drain valve Open the Fill/Drain valve and fill chillerCheck the coolant level Change the minimum operating temperatureChecking Refrigerant Charge Connect the ground wire to grounding lug Connecting Main Power SourceChecking Electrical Connections Close the electrical enclosure Turn on main power sourceOpen electrical enclosure Check the compressor Initially Starting ChillerPress the Start Chiller button Check the rotation of the pumpStopping the Chiller Operation Display TIC Control FeaturesCheck that the casters are locked Before StartingStarting Stopping Chiller Press the Up/Down arrows Changing SettingsChanging Setpoint Temperature Press Menu button onceChanging to Auto Tune Mode Changing Temperature ScaleApply a load to the Chiller Changing Auto Tune ModeUse the Up/Down arrows to change Press Enter buttonSetting the to Process LOW Limit Maintenance Maintenance Features UGH016/0500 Series 1 Portable Chillers, TIC Control Checking refrigerant site glass Preventative Maintenance ScheduleChecking electrical connections Inspecting the condenser coil for debrisInspecting condenser CleaningCleaning process fluid strainer Inspecting cooling water treatment systemCheck the refrigerant charge through the sight glass Cleaning Evaporator or WATER-COOLED Condenser Use a flashlight to check between coil surfaces Cleaning AIR-COOLED CondenserCoil cleaner Inspect the coilsBe sure the main power is disconnected Refill the reservoir Disconnect and lockout power to the chillerChecking Reservoir Level Locate the fill port on the back of the chillerTroubleshooting FEW Words of Caution Before BeginningDAY Time Identifying Cause ProblemPump Compressor Alarm Condition Description Status Answering AN AlarmPower is not reaching the chiller Control ProblemsThere is a problem with the control panel Input voltage is incorrect There is a phase loss Symptom Possible cause SolutionMechanical Conditions Failed Level switchWater level in tank is low Low Low supply voltage Faulty contactorFaulty overload module Pump Overload Overload set incorrectly. pump and compresOverload set incorrectly Alarm Possible causeClogged/dirty air-cooled Valve closed Compressor dischargeNo or low flow with a Failed flow switchPressure switch is FaultyLeads are backwards Compressor failed Contact Conair ServiceSlide the top of the switch housing over until Checking Replacing SwitchesCheck the switch Replace the switches as neededRemove the contactor by snapping off Disconnect the wiring from the contactorReconnect the wiring and reconnect power Replacing the ContactorChecking and Replacing Contact Conair Service for the temperature Replacing Temperature ControllerSlide the new controller in until Rating of compressor, fan or pump Reconnect wires and leadsRestore power to the chiller Replacing Overload ModulesRemove and replace fuses Replacing FusesOpen the drain/fill valve Remove the pump assemblyInspect, clean, and replace pump parts Removing Pump ComponentsCheck the connections Checking Pressure SwitchesLocate the pressure switch DAY TimeMake sure it corresponds to the following conditions Check the continuity within the switchPage From outside the United States, call WE’RE Here to Help2SERVICE Information Warranty Information Date Maintenance Item Maintenance LOGPage Pressure Appendix C-2 TablesDisplay Parameter Description Setting Units Control SettingsPage Parts & Diagrams Part Number Description Recommended Spare PartsSpare Parts P/D-3 4SPARE Parts Spare Parts P/D-5 6SPARE Parts