Grizzly G1021 instruction manual Bed Rollers, To Adjust the BED Rollers

Page 23

4.Remove the springs that are in the holes left by the setscrews. See Figure 22.

5.Check for any dirt or grit. Clean the springs and setscrews if dirty.

6.Screw the three regular-pressure setscrews back in until they are flush with the top of the head casting.

7.Screw the light pressure setscrew until it is approximately 14" above the head casting. The feed chain applies additional tension to the right side of the outfeed roller, so the pressure added by the setscrew need not be as high.

Pressure Setscrew

 

Pressure Spring

 

Roller

 

Check Nut

Height Setscrew

Figure 22. Roller pressure assembly.

Bed Rollers

The bed rollers ease stock movement through the planer. The height of the bed rollers will vary depending on the types of wood you will be plan- ing. When planing rough stock, set the rollers slightly high to keep the lumber from dragging along the bed. However, snipe may be unavoid- able. Smooth lumber should be planed with the rollers set just above the plane of the table. This will minimize snipe.

TO ADJUST THE BED ROLLERS:

1.Ensure that power is disconnected and lay a high quality straightedge across both table rollers. Use a try square to keep the straight- edge perpendicular to the table.

2.Use a feeler gauge to measure the clear- ance between the bottom of the straight edge and the table. Ideal clearance is between 0.002" and 0.005". Measure in sev- eral places. This measurement must be con- sistent across the entire table. See Figure 23.

Figure 23. Inspecting bed roller height.

3.Loosen the setscrews on both sides of each bed roller. See Figure 24.

4.Use a wrench to turn the eccentric shafts which adjust roller height. Stop turning when the table rollers are at the proper height.

5.Once your roller heights are correct, re-tight- en all the setscrews.

6.Check the height of the table rollers. Repeat steps 1-5 until the bed rollers are properly set. Spin the bed rollers to ensure free move- ment.

G1021 15" Planer

-23-

Image 23
Contents Planer Page Table Of Contents Adjustment Block Pattern Warranty and Returns Safety Instructions For Power Tools SafetySafety Instructions For Power Tools Additional Safety Instructions For Planers Extension Cords FusingCircuit Requirements 220V Operation GroundingCommentary IntroductionParts Inventory UnpackingSite Considerations Clean UpOptional Stand AssemblyOverview To Mount the Planer Starter SwitchPlaner Unit To Mount the Handwheel Handwheel Knife Setting JigTo Assemble the Knife Setting JIG To Attach the Dust Port Extension Rollers Dust PortTo Attach the Extension Rollers Overview of planer adjustment controls G1021 15 Planer AdjustmentsTo Check Table Parallelism Table AdjustmentGauge Block To Inspect the Knives Knife InspectionTo SET the Knives Knife SettingChip Breaker To Adjust the ChipbreakerTo Check Roller Height Feed Roller HeightFeed Roller Pressure To Adjust Roller HeightTo Adjust Roller Pressure Bed Rollers To Adjust the BED RollersChip Deflector To Adjust the Chip DeflectorAnti-KickbackBelts To INSPECT/ADJUST the PulleysTo Inspect the Gearbox GearboxTo Check Belt Tension Extension Rollers Extension RollersThickness Scale To Adjust the ScaleTable Locks OperationsDepth Limiter Power FeedHandwheel Type Shear PSI Test Run Wood SpeciesPlaning Difficulties GeneralKnives MaintenanceFill Drain LubricationAdjustment Section Closure Symptom Possible Cause Corrective Action TroubleshootingReference 145 79 80 146 See page 41-42 for Reference Number Listing See page 41-42 for Reference Number Listing Pulley Cover PK06M G1021 15 Planer Warranty and Returns