Grizzly G1021 Circuit Requirements, 220V Operation Grounding, Fusing, Extension Cords

Page 8

SECTION 2: CIRCUIT REQUIREMENTS

220V Operation

 

Grounding

 

 

 

 

 

 

The G1021 Planer motor is wired to operate at 220V only. A cordset without a 220V plug is included with the Model G1021. Plugs and recep- tacles can be purchased at your local hardware store or home center. When connecting to 220V, ensure that the electrical circuit is in fact a 220V circuit. Contact your local electrical contractor if uncertain about converting to 220V operation.

When operating at 220V, we recommend using a NEMA-style 6-15 plug and outlet as depicted in Figure 1. You may also “hard-wire” the planer directly to your panel, provided you place a dis- connect switch near the machine. Check the electrical codes in your area for specifics on wiring requirements.

Figure 1. NEMA 6-15 220V/15A connector.

Fusing

Under normal load, the Model G1021 draws about 12 amps. We recommend a 15-amp circuit or a 20-amp slow-blow fuse. A circuit rated any higher will not adequately protect the motor.

Equipment returned to us for service that shows evidence of being over-fused will be repaired or replaced totally at the customer’s expense, regardless of the present warranty status.

-8-

In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric cur- rent. This tool is equipped with a power cord hav- ing an equipment-grounding conductor. The out- let must be properly installed and grounded in accordance with all local codes and ordinances.

WARNING

This equipment must be grounded. Please ensure that this machine is continuously grounded from the motor to the machine frame and then to a known ground. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate 12 A.W.G. copper grounding wire from the outlet to a known ground. Under no circumstances should the grounding pin from any three-pronged plug be removed. Serious injury may occur.

Extension Cords

If used, extension cords must be rated hard ser- vice – grade S – or better. Conductor size must be 12 AWG for cords up to 50 feet in length. Your extension cord must also contain a ground wire and plug pin. To ensure safe and dependable machine performance, inspect cords frequently for wear or damage. Replace or repair the cord immediately if evidence of damage is apparent.

G1021 15" Planer

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Planer Page Table Of Contents Adjustment Block Pattern Warranty and Returns Safety Safety Instructions For Power ToolsSafety Instructions For Power Tools Additional Safety Instructions For Planers Fusing Circuit Requirements220V Operation Grounding Extension CordsIntroduction CommentaryUnpacking Parts InventoryClean Up Site ConsiderationsOptional Stand AssemblyOverview To Mount the Planer Starter SwitchPlaner Unit To Mount the Handwheel Handwheel Knife Setting JigTo Assemble the Knife Setting JIG To Attach the Dust Port Extension Rollers Dust PortTo Attach the Extension Rollers Adjustments Overview of planer adjustment controls G1021 15 PlanerTo Check Table Parallelism Table AdjustmentGauge Block Knife Inspection To Inspect the KnivesKnife Setting To SET the KnivesTo Adjust the Chipbreaker Chip BreakerFeed Roller Height To Check Roller HeightFeed Roller Pressure To Adjust Roller HeightTo Adjust Roller Pressure To Adjust the BED Rollers Bed RollersTo Adjust the Chip Deflector Chip DeflectorTo INSPECT/ADJUST the Pulleys Anti-KickbackBeltsTo Inspect the Gearbox GearboxTo Check Belt Tension Extension Rollers Extension RollersTo Adjust the Scale Thickness ScaleOperations Table LocksDepth Limiter Power FeedHandwheel Test Run Wood Species Type Shear PSIPlaning Difficulties Maintenance GeneralKnivesLubrication Fill DrainAdjustment Section Closure Troubleshooting Symptom Possible Cause Corrective ActionReference 145 79 80 146 See page 41-42 for Reference Number Listing See page 41-42 for Reference Number Listing Pulley Cover PK06M G1021 15 Planer Warranty and Returns
Top Page Image Contents