Envision Peripherals IM1609 08, IM1609 10 Dimensional Data Extended Slope Top Cabinet, NCE09-18

Page 8

ENVISION CONSOLE INSTALLATION MANUAL

Dimensional Data - Extended Slope Top Cabinet

NCE09-18

@756B@3BC@<

B=>

:34B@3BC@<

4

2

3

/

/	47:B3@0@/193B	1

0 5

47:B3@0@/193B	0

23B/7:/

BE7AB3FB3<232B/0 0/19/<24=@B6C<B7: B/00@3/9A=44 =<:G0@3/9=44 B/0A/;3A723/A 5@7::3:72/AA6=E<

@3;=D3>:/AB71AB@7> 4@=;0@=93<B/0/<2 @3>:/13=<0@=93< 3253=4:35/AA6=E<

6

4@=<B

7

8

23B/7:0

BE7AB3FB3<232B/0 0/19/<24=@B6C<B7: B/00@3/9A=44 =<:G0@3/9=44 B/0A/;3A723/A 5@7::3:72/AA6=E<

@3;=D3>:/AB71AB@7> 4@=;0@=93<B/0/<2 @3>:/13=<0@=93< 3253=4:35/AA6=E<

	Ext. Slope Top		Overall Cabinet

			A	B	C	D	E	F	G	H	I	J
	Configuration
			Width	Depth	Height	Grille Lid	Grille	Grille
							Length	Width
	09-12	in.	50.0	12.6	29.1	9.2	35.0	6.1	2.4	49.1	12.0	4.3
		cm.	127.0	32.0	73.9	23.4	88.9	15.6	6.1	124.7	30.5	10.9

	15-18	in.	55.0	12.6	29.1	9.2	35.0	6.1	2.5	54.1	11.8	4.3
		cm.	139.7	32.0	73.9	23.4	88.9	15.6	6.4	137.4	29.8	10.9

7

Image 8

Contents Envision Console Installation Manual Page Table of Contents Model Nomenclature NC C General Installation Information Safety Considerations Refrigerant Systems Moving and StorageDimensional Data Flat Top Cabinet NCW09-18Dimensional Data Slope Top Cabinet ConfigurationNCS09-18 Slope TopExt. Slope Top Dimensional Data Extended Slope Top CabinetNCE09-18 Dimensional Data Right Return Controls Detail Dimensional Data Right Return Chassis Dimensional Data Left Return Controls Detail Dimensional Data Left Return Chassis #Installation Steps Mark Unit PositionProvide Water and Condensate Drain Connections Pipe LocationsProvide Line Voltage Wiring Chassis InstallationFinal Electrical Connection Final Water ConnectionField Converting Console Top view Side viewGround Source Loop System Checkout System Cleaning and FlushingCleaning and Flushing Open Loop Ground Water Systems Water QualityMicroprocessor Remote Thermostat Wiring Electrical ConnectionsAuxiliary Heat Ratings GeneralUnit Electrical Data Fan Performance DataWiring Schematic 208-230-265/60/1CCM w/EH Electronic Thermostat 208-230-265/60/1 Control ModuleLED Display Mode Table 208-230-265/60/1 Schematic a Versatec Control EH & Remote Wall ThermostatFX10 EH 208-230-265/60/1 PSCStandard CCM Control Features Envision Console ControlsOptional Versatec Microprocessor Control Features Logic Board DIP Switch Settings Control Tables for Optional Versatec MicroprocessorOptional FX10 Control Control Timing & Fault Recognition Delays Standard FeaturesOptional FX10 Microprocessor and BAS Interface Zone SensorsControl and Safety Feature Details Sequence of OperationRandom Start Delay Compressor Fixed On Delay TimeCompressor Minimum On Delay Compressor Short Cycle Delay TimeInputs & Outputs Configuration Control AccessoriesInfo Status Temps Outputs Settings FX10 User Interface MUI Physical Layout Login Required N2 Open LonWorks LonWorks Point DescriptionBACNet BACnet Point DescriptionBACnet Variables Analog Input TypeAnalog Output Type Analog Value TypeMultistate Input Type Multistate Output TypeHydronic Loop Controller for Boiler/Tower Installations Unit Startup NotesEmergency Electric Resistance Heat Electrical DisconnectStartup Steps Unit Startup Checklist / Unit Startup StepsBefore Powering Unit, Check The Following Single Speed Models Unit Operating ParametersUnit Operating Limits Startup/Troubleshooting Form Pressure Drop Preventive Maintenance Replacement ProceduresWater Coil Maintenance Other MaintenancePage Envision Series Console