Envision Peripherals IM1609 10, IM1609 08 BACnet Variables, Analog Input Type, Analog Output Type

Page 39

ENVISION CONSOLE INSTALLATION MANUAL

Envision Console Controls

BACnet Variables

The variables will be listed with the point type and instance preceding the variable name.

Analog Input (Type 0)

0:1 Space Temp

[Read only, shows the space temperature] 0:2 Discharge Air Temp

[Read only, field mounted sensor unless supplied as a factory special]

0:3 Effective Clg Setpt

[Read only, shows the active cooling setpoint] 0:4 Effective Htg Setpt

[Read only, shows the active heating setpoint] 0:5 Space Humidity

[Read]

0:6 Water Coil Temp

[Read, shows the refrigerant temperature at its coldest, for predictive freeze condition detection]

0:7 Low Temp Limit

[Read, shows the water coil low temperature (freeze sensing) limit that will result in unit shutdown.]

0:8 ECM Cmd Output

[Read, shows the commanded speed (0-100%) of the ECM Blower]

0:9 Alarms Enumerated

[Read only, 0=no alarms, 1=condensate alarm, 2=Compressor Hi Discharge Pressure alarm, 3=Compressor low Suction Pressure alarm, 4=Freeze sensing alarm, 8=Faulty Freeze Sensor alarm, 9=Loss of Charge]

0:10 AO2 Value

[Read, shows the output value (0-100%) of AO2]

Analog Output (Type 1)

1:1 Space Setpoint

[Write, Raise and lower the heating and cooling setpoints from a single command point(volatile, reverts to ‘uncommanded’ after power outage).]

1:2 ECM Fan Ovrd

[Write, allows network direct control of the ECM blower speed (volatile, reverts to ‘uncommanded’ after power outage)]

1:3 AO2 Override

[Write, allows network direct control of the Analog Output 2, volatile, reverts to ‘uncommanded’ after power outage)]

1:4 Space temp Ovrd

[Write, allows the network to send space temperature values to the heat pump controller, volatile, these will supersede any temperature sensor connected to the space temperature Analog Input.]

Analog Value (Type 2)

2:1 Occupied Cool

[Write, Cooling setpoint in Occupied mode] 2:2 Unoccupied Cool

[Write, Cooling setpoint in Unoccupied mode] 2:3 Occupied Heat

[Write, Heating setpoint in Occupied mode] 2:4 Unoccupied Heat

[Write, Heating setpoint in Unoccupied mode] 2:5 Temporary Occ Time

[Write, set the duration of the temporary occupancy timer which is initiated by pressing the button on the zone sensor]

2:6 Remote Setpt Span

[Write, sets the offset range that the setpoint knob on the zone sensor may apply to the effective Htg/ Clg setpoints]

2:7 Remote Setpt Bias

[Write, biases the entire readjust range of the remote setpoint adjust to allow zeroing from the network.]

2:8 Space Temp Offset

[Write, Adds an offset to the Space Temp value for calibration]

2:9 Dehumidify Setpt

[Write, sets the humidity value that will cause the heat pump to enter passive dehumidification]

2:10 Low Temp Limit Adj

[Write, sets the water coil low temperature (freeze sensing) limit for shutdown]

Binary Input (Type 3)

3:1 Fan Cmd Status

[Read, show the commanded condition of the Fan Output,Inactive=Off, Active=On]

3:2 Comp Cmd Status

[Read, show the commanded condition of the Compressor Output, Inactive=Off, Active=On]

3:3 Comp Hi Capacity Cmd

[Read, show the commanded condition of the ‘Hi Capacity’ Compressor control, Inactive=Off, Active=On.]

3:4 Reversing Valve

[Read, show the commanded condition of the Reversing Valve Output, Inactive =Heating, Active =Cooling]

3:5 Accessory 1 Output

[Read, Shows the commanded value of the X1 (Accessory

3:8 Alarm Status

[Read, shows the in alarm/out of alarm status, Inactive=Off, Active=On]

38

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Envision Console Installation Manual Page Table of Contents NC C Model NomenclatureMoving and Storage General Installation InformationSafety Considerations Refrigerant SystemsNCW09-18 Dimensional Data Flat Top CabinetSlope Top Dimensional Data Slope Top CabinetConfiguration NCS09-18Dimensional Data Extended Slope Top Cabinet NCE09-18Ext. Slope Top Dimensional Data Right Return Controls Detail  Dimensional Data Right Return ChassisDimensional Data Left Return Controls Detail # Dimensional Data Left Return ChassisMark Unit Position Installation StepsPipe Locations Provide Water and Condensate Drain ConnectionsFinal Water Connection Provide Line Voltage WiringChassis Installation Final Electrical ConnectionTop view Side view Field Converting ConsoleSystem Cleaning and Flushing Cleaning and FlushingGround Source Loop System Checkout Water Quality Open Loop Ground Water SystemsGeneral Microprocessor Remote Thermostat WiringElectrical Connections Auxiliary Heat RatingsFan Performance Data Unit Electrical Data208-230-265/60/1 Wiring SchematicControl Module CCM w/EH Electronic Thermostat 208-230-265/60/1LED Display Mode Table Versatec Control EH & Remote Wall Thermostat 208-230-265/60/1 Schematic aPSC FX10 EH 208-230-265/60/1Envision Console Controls Standard CCM Control FeaturesOptional Versatec Microprocessor Control Features Control Tables for Optional Versatec Microprocessor Logic Board DIP Switch SettingsOptional FX10 Control Zone Sensors Control Timing & Fault Recognition DelaysStandard Features Optional FX10 Microprocessor and BAS InterfaceSequence of Operation Control and Safety Feature DetailsCompressor Short Cycle Delay Time Random Start DelayCompressor Fixed On Delay Time Compressor Minimum On DelayControl Accessories Inputs & Outputs ConfigurationFX10 User Interface MUI Physical Layout  Info Status Temps Outputs SettingsLogin Required N2 Open LonWorks Point Description LonWorksBACnet Point Description BACNetAnalog Value Type BACnet VariablesAnalog Input Type Analog Output TypeMultistate Output Type Multistate Input TypeElectrical Disconnect Hydronic Loop Controller for Boiler/Tower InstallationsUnit Startup Notes Emergency Electric Resistance HeatUnit Startup Checklist / Unit Startup Steps Before Powering Unit, Check The FollowingStartup Steps Unit Operating Parameters Unit Operating LimitsSingle Speed Models Startup/Troubleshooting Form Pressure Drop Other Maintenance Preventive MaintenanceReplacement Procedures Water Coil MaintenancePage Envision Series Console

IM1609 10, IM1609 08 specifications

Envision Peripherals has carved a niche in the realm of advanced display technology, and its IM1609 10 and IM1609 08 models are no exception. These cutting-edge monitors are designed to meet a wide array of professional needs while delivering outstanding performance and visual clarity.

One of the standout features of the IM1609 10 is its impressive 16:9 aspect ratio and full HD resolution. This setup ensures that users receive crisp and vibrant visuals, whether they're working on intricate designs, analyzing data, or enjoying multimedia content. The IM1609 08 shares similar visual capabilities, making both models ideal for professionals in graphic design, video editing, and other visually intensive fields.

Both displays incorporate advanced LED backlight technology, which not only enhances color accuracy but also contributes to energy efficiency. Users can expect deeper blacks and brighter whites, resulting in a more dynamic visual experience. Furthermore, the IM1609 series features wide viewing angles, allowing multiple users to view the screen simultaneously without loss of quality or color distortion.

In terms of connectivity, the IM1609 10 and IM1609 08 come equipped with a range of ports, including HDMI, DisplayPort, and USB-C. This versatility ensures seamless integration with various devices, from laptops and desktops to media players and more. The USB-C port also allows for quick data transfer and charging options, catering to the needs of modern tech users.

Ergonomics is another key characteristic of the IM1609 series. With adjustable stands that allow for height, tilt, and swivel adjustments, users can customize their viewing experience for maximum comfort, reducing neck and eye strain during long working hours.

Additionally, the IM1609 monitors feature built-in blue light filters and flicker-free technology, which help to create a healthier viewing environment by minimizing eye fatigue. This consideration for user well-being is increasingly important in today’s tech-driven world, especially for professionals who spend significant time in front of screens.

Overall, Envision Peripherals’ IM1609 10 and IM1609 08 models represent the company’s commitment to blending performance, usability, and comfort into one seamless package. Whether for professional or personal use, these monitors deliver exceptional quality, making them a noteworthy addition to any workspace.
Top Page Image Contents