Envision Peripherals IM1609 10, IM1609 08 Unit Startup Notes, Emergency Electric Resistance Heat

Page 41

ENVISION CONSOLE INSTALLATION MANUAL

Unit Startup Notes

Emergency Electric Resistance Heat

A factory-installed emergency electric heater package is available. Rated for 2,000 watts on models NC09 through NC12 and 3,000 watts on models NC15 through NC18.

The heater package consists of ni-cad elements, ceramic insulators, and thermal limit switches. A concealed, chassis mounted rocker switch controls the heater mode operation and allows the field installation of an aquastat for boilerless unit operation.

Hydronic Loop Controller for

Boiler/Tower Installations

The hydronic loop controller is a microprocessor based control panel for control of water loop heat rejector (tower), heat supplier (boiler), and/or water well pumps and circula- tion pumps. Includes audible and visual alarms, temperature indication, and add-on options of low switches, remote alarm sensor wells and pump alternator.

Electrical Disconnect

Field installed on the optional chassis back plate, the con- sole disconnect provides a permanent electrical connection to the main electrical supply branch. Wiring between the disconnect and the unit chassis is field supplied and allows the electrical power source to the chassis to be interrupted for unit servicing.

Non-Fused

Constructed of heavy gauge galvanized steel, the rocker style disconnect switch provides reliable electri- cal control. Wiring pigtails, using 12-gauge wires, are factory installed to simplify field wiring.

Fused

Similar in construction to the non-fused electrical disconnect. The fused disconnect is available in five models with equipment rated fuses to provide addi- tional circuit protection. The fuses are panel mounted to allow easy inspection and removal without removing the cover on the disconnect.

CFD-10

- 10 amp rated fuse

CFD-12

-

12 amp rated fuse

CFD-15

-

15 amp rated fuse

CFD-20

- 20 amp rated fuse

CFD-25

- 25 amp rated fuse

Motorized Outside Air Damper

A field installed motorized outside air damper is available to allow the introduction of fresh air into the conditioned space through an outside vent. The damper motor is pow- ered by 24 volts with a spring-close design in the event of a power failure. The damper blade and housing are con- structed of aluminum for corrosion resistance and the blade includes a neoprene gasket to prevent air infiltration during off cycles. The damper assembly is installed on the optional chassis back plate and a two-wire low voltage connection simplifies wiring. A concealed, chassis mounted rocker switch allows the damper to be disabled

40

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Envision Console Installation Manual Page Table of Contents NC C Model NomenclatureSafety Considerations General Installation InformationRefrigerant Systems Moving and StorageNCW09-18 Dimensional Data Flat Top CabinetConfiguration Dimensional Data Slope Top CabinetNCS09-18 Slope TopExt. Slope Top Dimensional Data Extended Slope Top CabinetNCE09-18 Dimensional Data Right Return Controls Detail  Dimensional Data Right Return ChassisDimensional Data Left Return Controls Detail # Dimensional Data Left Return ChassisMark Unit Position Installation StepsPipe Locations Provide Water and Condensate Drain ConnectionsChassis Installation Provide Line Voltage WiringFinal Electrical Connection Final Water ConnectionTop view Side view Field Converting ConsoleGround Source Loop System Checkout System Cleaning and FlushingCleaning and Flushing Water Quality Open Loop Ground Water SystemsElectrical Connections Microprocessor Remote Thermostat WiringAuxiliary Heat Ratings GeneralFan Performance Data Unit Electrical Data208-230-265/60/1 Wiring SchematicControl Module CCM w/EH Electronic Thermostat 208-230-265/60/1LED Display Mode Table Versatec Control EH & Remote Wall Thermostat 208-230-265/60/1 Schematic aPSC FX10 EH 208-230-265/60/1Envision Console Controls Standard CCM Control FeaturesOptional Versatec Microprocessor Control Features Control Tables for Optional Versatec Microprocessor Logic Board DIP Switch SettingsOptional FX10 Control Standard Features Control Timing & Fault Recognition DelaysOptional FX10 Microprocessor and BAS Interface Zone SensorsSequence of Operation Control and Safety Feature DetailsCompressor Fixed On Delay Time Random Start DelayCompressor Minimum On Delay Compressor Short Cycle Delay TimeControl Accessories Inputs & Outputs ConfigurationFX10 User Interface MUI Physical Layout  Info Status Temps Outputs SettingsLogin Required N2 Open LonWorks Point Description LonWorksBACnet Point Description BACNetAnalog Input Type BACnet VariablesAnalog Output Type Analog Value TypeMultistate Output Type Multistate Input TypeUnit Startup Notes Hydronic Loop Controller for Boiler/Tower InstallationsEmergency Electric Resistance Heat Electrical DisconnectStartup Steps Unit Startup Checklist / Unit Startup StepsBefore Powering Unit, Check The Following Single Speed Models Unit Operating ParametersUnit Operating Limits Startup/Troubleshooting Form Pressure Drop Replacement Procedures Preventive MaintenanceWater Coil Maintenance Other MaintenancePage Envision Series Console

IM1609 10, IM1609 08 specifications

Envision Peripherals has carved a niche in the realm of advanced display technology, and its IM1609 10 and IM1609 08 models are no exception. These cutting-edge monitors are designed to meet a wide array of professional needs while delivering outstanding performance and visual clarity.

One of the standout features of the IM1609 10 is its impressive 16:9 aspect ratio and full HD resolution. This setup ensures that users receive crisp and vibrant visuals, whether they're working on intricate designs, analyzing data, or enjoying multimedia content. The IM1609 08 shares similar visual capabilities, making both models ideal for professionals in graphic design, video editing, and other visually intensive fields.

Both displays incorporate advanced LED backlight technology, which not only enhances color accuracy but also contributes to energy efficiency. Users can expect deeper blacks and brighter whites, resulting in a more dynamic visual experience. Furthermore, the IM1609 series features wide viewing angles, allowing multiple users to view the screen simultaneously without loss of quality or color distortion.

In terms of connectivity, the IM1609 10 and IM1609 08 come equipped with a range of ports, including HDMI, DisplayPort, and USB-C. This versatility ensures seamless integration with various devices, from laptops and desktops to media players and more. The USB-C port also allows for quick data transfer and charging options, catering to the needs of modern tech users.

Ergonomics is another key characteristic of the IM1609 series. With adjustable stands that allow for height, tilt, and swivel adjustments, users can customize their viewing experience for maximum comfort, reducing neck and eye strain during long working hours.

Additionally, the IM1609 monitors feature built-in blue light filters and flicker-free technology, which help to create a healthier viewing environment by minimizing eye fatigue. This consideration for user well-being is increasingly important in today’s tech-driven world, especially for professionals who spend significant time in front of screens.

Overall, Envision Peripherals’ IM1609 10 and IM1609 08 models represent the company’s commitment to blending performance, usability, and comfort into one seamless package. Whether for professional or personal use, these monitors deliver exceptional quality, making them a noteworthy addition to any workspace.
Top Page Image Contents