Husqvarna DXR-310 manual Manoeuvring, General, Outriggers, Rotation function, Arm system

Page 10

SAFETY INSTRUCTIONS

Manoeuvring

General

•If several machines are used at the same workplace there is a risk of mixing up the remote controls.

Switch on the current to the remote control and the machine. Press the horn to see which machine is connected to the remote control. The machine will beep and ßash three times. Do not activate the remote control before you have ensured that the correct machine is being operated.

•Wait until the remote control has been turned off and the motor has stopped before you enter into the machine’s risk area.

•Never leave the machine unsupervised with the motor running.

•The machine can overturn during work. During op- eration the machine must be positioned as level as possible and the outriggers must be fully extended.

•In some cases it can be difÞcult to determine which end of the machine is the front and which is the rear. Look at the direction markings on the sides of the machine’s tracks to avoid incorrect operation.

Outriggers

•When the outriggers are folded, the arm must be retracted to minimize the risk of the machine over- turning.

•The machine’s outriggers can leave the ground, especially when working with a hydraulic hammer or bucket. The higher the machine rises the greater the load the rest of the support mechanism is subject to.

•When working with a hydraulic hammer there is an increased risk of the machine tipping or landing with a large force on the outrigger on impact. Take this risk into account and institute appropriate safety measures to avoid any personal injury or mechanical damage.

Rotation function

•If there is a breakdown in the machine’s rotation mechanism the machine’s upper part may rotate freely, potentially causing personal injury or me- chanical damage. Keep your distance.

•The machine is most stable when working directly forwards or backwards. When the machine’s upper part rotates to the side, the outriggers should be down and the arm system manoeuvred so that it is as close to the ground as possible.

•In some cases it can be difÞcult to predict the direction of rotation. Operate the turning motion carefully until you have apprehended the direction of rotation.

Arm system

•Do not use the arm system and the rotation func- tion for striking, demolishing or scraping.

•Do not work with the arm if the machine’s outrig- gers are folded. The outriggers provide stability and reduce the risk of the machine tipping.

•When the arm system’s reach is being used, the load increases as does the risk of tipping. Posi- tion the machine as close to the working object as possible.

•Never use the telescopic arm to press the tool against the working object.

•Do not secure the machine to Þxed objects, e.g. walls, to increase the force on the working object. Both the machine and the tool can be subject to overloading.

•Do not work with the machine’s cylinders in the inner or outer end positions to avoid overloading. Leave a few centimetres to the maximum position. The hydraulic ßuid then has a greater capacity to alleviate impacts and vibrations.

•There are two working positions that put a lot of strain on individual cylinders.

Cylinders 1 and 2 are in their outer positions and the hammer is working in the upward direction. Never operate the cylinders to their end positions.

Cylinder 3 is in its outer position and the hammer is working in the downward direction. Never operate the cylinders to their end positions.

10 - English

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DXR-310 Page Contents Introduction KEY to Symbols Symbols on the machinePersonal protective equipment Safety InstructionsProtective equipment Other protective equipmentIf there is an accident General safety instructionsManagement and operator ResponsibilityGeneral working instructions Work area safetyElectrical safety Machine’s risk areaGeneral Personal safetyOperation Education and trainingOutriggers ManoeuvringGeneral Rotation functionFalling material Transport and storage TowingMaintenance and service Machine’s safety featuresPersonal protection Mechanical protection Moisture TemperatureExternal environmental factors Dust and particlesPresentation Machine’s functionsWhat is what in the machine Main pressure Hydraulic SystemGeneral Pressure cut-offMachine’s hydraulic system High-voltage circuit Electric SystemLow-voltage circuit Machine’s electric system Control System Remote controlBattery Machine’s softwareWhat is what on the remote control Symbols on the remote control Starting Starting and StoppingBefore starting StoppingOperating modes Key to commandsOperation Designation of the machine’s partsWork mode Set-up mode Track operationTransport mode Hydraulic hammer ToolsBucket Concrete cutterFitting CleaningChanging tools StorageTrack widener SettingsFitting the track widener Menu system Tuning Operational settingsLCD Adjustment Software versionMaintenance and Service Cleaning of components CleaningCleaning method After washingService schedule Daily inspectionWeekly service MiscellaneousAfter the Þrst 100 hours Hours serviceChange Outriggers and arm system Service reviewLubrication Gear ringTightening torque MountingsShafts PosLevel check Wear and damageLeakage CracksFunctional inspection Draining hydraulic ßuid ChangeReplenishing hydraulic ßuid Oil Þlter Air ÞlterService messages Trouble ShootingError messages Service messages and actions ActionTrouble shooting guide Fault Cause Possible actionEnglish Hydraulic system’s pressure Technical DataGuide values for mains connection 50 HzHydraulic ßuid Preset limit valuesHydraulic ßuid and lubricant LubricantTechnical data Machine without tool Sound power levelNoise emissions Machine with tool hydraulic hammerEnglish Technical Data EC-DECLARATION of Conformity EC-declaration of conformityPage ´z+SXh¶6Q¨ Page 1151567-26 2009-03-16

DXR-310 specifications

The Husqvarna DXR-310 is a state-of-the-art remote-controlled demolition robot designed for various construction and demolition tasks. With an emphasis on versatility and efficiency, this robust machine stands out in the crowded landscape of demolition equipment. It is specifically engineered to tackle challenging environments while offering operators a high level of safety and control.

One of the standout features of the DXR-310 is its powerful hydraulic system, which allows for exceptional performance even in the most demanding applications. With an output of 12.5 kW, it can handle various attachments effectively, enabling it to perform a wide array of tasks, from crushing and breaking to lifting and demolition. Its compact size and lightweight design make it easy to maneuver, which is particularly beneficial in confined spaces, such as renovation projects or urban environments.

The DXR-310 is equipped with a user-friendly control system that facilitates precise operation from a distance. The ergonomic remote control is intuitive, allowing the operator to execute complex commands with ease, enhancing overall productivity. This feature is vital, especially in situations where operator safety is paramount, as it enables them to maintain a safe distance from potential hazards.

Another notable characteristic is the robot's durability and reliability. The chassis and components are designed to withstand harsh working conditions, ensuring long-term performance. The robust build minimizes downtime, enhancing overall efficiency on job sites.

The Husqvarna DXR-310 also integrates advanced technology to optimize its functionality. It is compatible with a range of attachments, including hydraulic breakers, crushers, and grapples, making it highly adaptable to various tasks. Additionally, the robot is designed with a unique suspension system that improves stability and ground contact, ensuring reliable operation on uneven surfaces.

In terms of maintenance, the DXR-310 is designed to be user-friendly, with accessible components that simplify routine checks and repairs. This commitment to easy maintenance contributes to reduced operational costs over time.

In conclusion, the Husqvarna DXR-310 demolition robot combines power, versatility, and safety into a single machine. Its advanced hydraulic system, user-friendly controls, and adaptability make it ideal for a wide range of demolition applications. The robust design and maintenance-friendly features further enhance its appeal to contractors looking for efficient solutions in the construction industry.
Top Page Image Contents