Husqvarna DXR-310 manual Mechanical protection

Page 14

SAFETY INSTRUCTIONS

Identity code

The remote control and the machine are connected by means of a pre-programmed ID code. The ID code ensures that the right remote control is used for the right machine.

If several machines are used at the same workplace there is a risk of mixing up the remote controls.

Switch on the current to the remote control and the machine. Press the horn to see which machine is con- nected to the remote control. The machine will beep and ßash three times. Do not activate the remote con- trol before you have ensured that the correct machine is being operated.

When steering the machine using cables, the ID code is suppressed and the same remote control can be used for different machines if these have the same control system version.

Automatic frequency hopping

In the event of interference in the communication, the frequency changes automatically to guarantee interfer- ence-free transmission.

Emergency stop/machine stop

When the machine stop on the remote control is pressed, the power to the circuits controlling the communication with the machine is interrupted. The machine engine stops due to the interruption of the transfer of signals to the machine’s electronic device.

The emergency stop on the machine switches off the main power to the machine.

Protective earth

The machine and its components are connected to grounding conductors in the power cable. If there is a fault, a fuse is tripped and the current is disconnected.

The machine must be connected to a power point with a protective earth. If there are no grounding conduc- tors, or if they are connected incorrectly, have come off or are loose in a terminal, the current will remain connected and touching the machine can be highly dangerous.

If there is reason to believe that the protective earth has been damaged, the machine must be turned off and the power cable removed until such time as the protective earth has been restored.

Always connect the machine through an earth-fault breaker with personal protection, i.e. an earth fault circuit breaker that trips at an earth fault of 30 mA.

Hydraulic brake

Hydraulic motors are used when moving the machine. All hydraulic motors are Þtted with brakes. These hydraulic motors contain counter balance valves that prevent uncontrolled ßow through the motor, e.g. when manoeuvring down a slope or when the machine is parked. The counter balance valve closes the tank opening when the drive motors are not being operated.

Mechanical brake

The machine’s drive motors are equipped with a me- chanical parking brake. The machine is braked until its drive function is activated.

Mechanical protection

Automatic phase rotation relay

The automatic phase rotation relay prevents the elec- tric motor starting with the wrong rotation direction thus causing mechanical damage.

Motor protection

To prevent overloading, the motor is equipped with bimetallic relays in the motor linings that disconnect the power if the motor gets too hot.

If the motor is too hot it is not possible to operate the tools. The rest of the machine’s functions can be run at half speed in order to facilitate evacuation of the machine from risky environments.

Once the motor’s temperature has fallen to a normal working temperature all functions can be used again.

The machine’s softstarter is Þtted with a motor cut-out that trips if the current is too high for too long a period. The machine’s functions return to normal position after three minutes.

Fuses

Fuses are used to protect the following components as well as to prevent Þre in conjunction with faults or if electrical components are overloaded.

Pressure relief valves

The machine’s hydraulic system is equipped with pressure relief valves. They protect the hydraulic system against too high pressure and the mechanical components against overloading.

Pump-around valve

The pump-around valve drains the hydraulic ßow into a tank and relieves the pressure on the hydraulic sys- tem. No pressure enters the cylinders and it prevents the risk of unforeseen movements. This happens, for example, after three seconds of inactivity.

14 - English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents DXR-310 Page Contents Introduction KEY to Symbols Symbols on the machinePersonal protective equipment Safety InstructionsProtective equipment Other protective equipmentIf there is an accident General safety instructionsManagement and operator ResponsibilityGeneral working instructions Work area safetyElectrical safety Machine’s risk areaGeneral Personal safetyOperation Education and trainingOutriggers ManoeuvringGeneral Rotation functionFalling material Transport and storage TowingPersonal protection Machine’s safety featuresMaintenance and service Mechanical protection Moisture TemperatureExternal environmental factors Dust and particlesPresentation Machine’s functionsWhat is what in the machine Main pressure Hydraulic SystemGeneral Pressure cut-offMachine’s hydraulic system Low-voltage circuit Electric SystemHigh-voltage circuit Machine’s electric system Control System Remote controlBattery Machine’s softwareWhat is what on the remote control Symbols on the remote control Starting Starting and StoppingBefore starting StoppingOperating modes Key to commandsOperation Designation of the machine’s partsWork mode Set-up mode Track operationTransport mode Hydraulic hammer ToolsBucket Concrete cutterFitting CleaningChanging tools StorageFitting the track widener SettingsTrack widener Menu system Tuning Operational settingsLCD Adjustment Software versionMaintenance and Service Cleaning of components CleaningCleaning method After washingService schedule Daily inspectionWeekly service MiscellaneousChange Hours serviceAfter the Þrst 100 hours Outriggers and arm system Service reviewLubrication Gear ringTightening torque MountingsShafts PosLevel check Wear and damageLeakage CracksFunctional inspection Replenishing hydraulic ßuid ChangeDraining hydraulic ßuid Oil Þlter Air ÞlterService messages Trouble ShootingError messages Service messages and actions ActionTrouble shooting guide Fault Cause Possible actionEnglish Hydraulic system’s pressure Technical DataGuide values for mains connection 50 HzHydraulic ßuid Preset limit valuesHydraulic ßuid and lubricant LubricantTechnical data Machine without tool Sound power levelNoise emissions Machine with tool hydraulic hammerEnglish Technical Data EC-DECLARATION of Conformity EC-declaration of conformityPage ´z+SXh¶6Q¨ Page 1151567-26 2009-03-16

DXR-310 specifications

The Husqvarna DXR-310 is a state-of-the-art remote-controlled demolition robot designed for various construction and demolition tasks. With an emphasis on versatility and efficiency, this robust machine stands out in the crowded landscape of demolition equipment. It is specifically engineered to tackle challenging environments while offering operators a high level of safety and control.

One of the standout features of the DXR-310 is its powerful hydraulic system, which allows for exceptional performance even in the most demanding applications. With an output of 12.5 kW, it can handle various attachments effectively, enabling it to perform a wide array of tasks, from crushing and breaking to lifting and demolition. Its compact size and lightweight design make it easy to maneuver, which is particularly beneficial in confined spaces, such as renovation projects or urban environments.

The DXR-310 is equipped with a user-friendly control system that facilitates precise operation from a distance. The ergonomic remote control is intuitive, allowing the operator to execute complex commands with ease, enhancing overall productivity. This feature is vital, especially in situations where operator safety is paramount, as it enables them to maintain a safe distance from potential hazards.

Another notable characteristic is the robot's durability and reliability. The chassis and components are designed to withstand harsh working conditions, ensuring long-term performance. The robust build minimizes downtime, enhancing overall efficiency on job sites.

The Husqvarna DXR-310 also integrates advanced technology to optimize its functionality. It is compatible with a range of attachments, including hydraulic breakers, crushers, and grapples, making it highly adaptable to various tasks. Additionally, the robot is designed with a unique suspension system that improves stability and ground contact, ensuring reliable operation on uneven surfaces.

In terms of maintenance, the DXR-310 is designed to be user-friendly, with accessible components that simplify routine checks and repairs. This commitment to easy maintenance contributes to reduced operational costs over time.

In conclusion, the Husqvarna DXR-310 demolition robot combines power, versatility, and safety into a single machine. Its advanced hydraulic system, user-friendly controls, and adaptability make it ideal for a wide range of demolition applications. The robust design and maintenance-friendly features further enhance its appeal to contractors looking for efficient solutions in the construction industry.
Top Page Image Contents