Husqvarna DXR-310 manual Control System, Remote control, Battery, Machine’s software

Page 22

CONTROL SYSTEM

General

The remote control, the electronics unit and the pilot control valves are the main components in the control system. The signals from the remote control are trans- mitted to the machine via bluetooth or via a cable. The electronic unit in the machine transmits the signals via the pilot control valves to the hydraulic system by converting electric current into hydraulic pressure.

Remote control

The machine is controlled from the remote control. Transmission of signals is either wireless, using blue- tooth, or via a cable.

The movement of the joysticks is proportional. A small movement means that the function moves slowly, a larger movement increases the function’s speed pro- portionally.

Signal transmission

Identity code

The remote control and the machine are connected by means of a pre-programmed ID-code. The code is built into the remote control’s bluetooth transmitter and the re- ceiver on the machine. The ID code cannot be changed.

There is a sticker on the bottom of the remote control and on the machine’s bluetooth module with a ID code. The ID code ensures that the right remote control is used for the right machine.

Wireless signal transmission

Wireless transmission of signals uses bluetooth tech- nology.

Automatic frequency hopping

In the event of interference in the communication, the frequency changes automatically to guarantee interfer- ence-free transmission.

Signal transmission using cables

Connecting a cable shuts off the wireless communica- tion.

When the machine is controlled by means of cables, the ID code is suppressed and the same remote con- trol can be used for different machines if these have the same control system version.

Battery

The battery is a Li-ion type. Operating time is about

8-10 hours per charge. Extreme cold impairs the bat- tery’s capacity and operating time. Operating time is also affected by the extent to which the display has been active.

To save the battery, the display goes into energy save mode after 20 seconds. After Þve minutes of inactiv- ity the remote control turns off automatically. To use it again, it must be turned off and on again.

A message appears on the display approx. 30 minutes before the battery is completely ßat. It is not possible to activate the remote control if the battery capacity is too low.

Charging the battery

Before using the remote control for the Þrst time the battery has to be charged.

Charging time for a ßat battery is approx. 2-3 hours. The diode is orange when charging starts and be- comes green when the battery is fully charged. When the battery is fully charged the charger supplies the battery with maintenance current until the battery is removed from the charger.

Keep the battery charger dry and protected against temperature ßuctuations.

The machine’s software

Contact your service workshop regarding problems with the machine’s software or for any updates that might be needed.

22 - English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents DXR-310 Page Contents Introduction KEY to Symbols Symbols on the machinePersonal protective equipment Safety InstructionsProtective equipment Other protective equipmentIf there is an accident General safety instructionsManagement and operator ResponsibilityGeneral working instructions Work area safetyElectrical safety Machine’s risk areaGeneral Personal safetyOperation Education and trainingOutriggers ManoeuvringGeneral Rotation functionFalling material Transport and storage TowingMaintenance and service Machine’s safety featuresPersonal protection Mechanical protection Moisture TemperatureExternal environmental factors Dust and particlesPresentation Machine’s functionsWhat is what in the machine Main pressure Hydraulic SystemGeneral Pressure cut-offMachine’s hydraulic system High-voltage circuit Electric SystemLow-voltage circuit Machine’s electric system Control System Remote controlBattery Machine’s softwareWhat is what on the remote control Symbols on the remote control Starting Starting and StoppingBefore starting StoppingOperating modes Key to commandsOperation Designation of the machine’s partsWork mode Set-up mode Track operationTransport mode Hydraulic hammer ToolsBucket Concrete cutterFitting CleaningChanging tools StorageTrack widener SettingsFitting the track widener Menu system Tuning Operational settingsLCD Adjustment Software versionMaintenance and Service Cleaning of components CleaningCleaning method After washingService schedule Daily inspectionWeekly service MiscellaneousAfter the Þrst 100 hours Hours serviceChange Outriggers and arm system Service reviewLubrication Gear ringTightening torque MountingsShafts PosLevel check Wear and damageLeakage CracksFunctional inspection Draining hydraulic ßuid ChangeReplenishing hydraulic ßuid Oil Þlter Air ÞlterService messages Trouble ShootingError messages Service messages and actions ActionTrouble shooting guide Fault Cause Possible actionEnglish Hydraulic system’s pressure Technical DataGuide values for mains connection 50 HzHydraulic ßuid Preset limit valuesHydraulic ßuid and lubricant LubricantTechnical data Machine without tool Sound power levelNoise emissions Machine with tool hydraulic hammerEnglish Technical Data EC-DECLARATION of Conformity EC-declaration of conformityPage ´z+SXh¶6Q¨ Page 1151567-26 2009-03-16

DXR-310 specifications

The Husqvarna DXR-310 is a state-of-the-art remote-controlled demolition robot designed for various construction and demolition tasks. With an emphasis on versatility and efficiency, this robust machine stands out in the crowded landscape of demolition equipment. It is specifically engineered to tackle challenging environments while offering operators a high level of safety and control.

One of the standout features of the DXR-310 is its powerful hydraulic system, which allows for exceptional performance even in the most demanding applications. With an output of 12.5 kW, it can handle various attachments effectively, enabling it to perform a wide array of tasks, from crushing and breaking to lifting and demolition. Its compact size and lightweight design make it easy to maneuver, which is particularly beneficial in confined spaces, such as renovation projects or urban environments.

The DXR-310 is equipped with a user-friendly control system that facilitates precise operation from a distance. The ergonomic remote control is intuitive, allowing the operator to execute complex commands with ease, enhancing overall productivity. This feature is vital, especially in situations where operator safety is paramount, as it enables them to maintain a safe distance from potential hazards.

Another notable characteristic is the robot's durability and reliability. The chassis and components are designed to withstand harsh working conditions, ensuring long-term performance. The robust build minimizes downtime, enhancing overall efficiency on job sites.

The Husqvarna DXR-310 also integrates advanced technology to optimize its functionality. It is compatible with a range of attachments, including hydraulic breakers, crushers, and grapples, making it highly adaptable to various tasks. Additionally, the robot is designed with a unique suspension system that improves stability and ground contact, ensuring reliable operation on uneven surfaces.

In terms of maintenance, the DXR-310 is designed to be user-friendly, with accessible components that simplify routine checks and repairs. This commitment to easy maintenance contributes to reduced operational costs over time.

In conclusion, the Husqvarna DXR-310 demolition robot combines power, versatility, and safety into a single machine. Its advanced hydraulic system, user-friendly controls, and adaptability make it ideal for a wide range of demolition applications. The robust design and maintenance-friendly features further enhance its appeal to contractors looking for efficient solutions in the construction industry.
Top Page Image Contents