Milwaukee 1-1/2 manual Tool Assembly, Installing Bits and Chisels Fig Spline Drive System Cat. No

Page 5

TOOL ASSEMBLY

WARNING!

To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous.

WARNING!

To reduce the risk of injury, always use a side handle when using this tool. Always brace or hold securely.

Adjusting the Side Handle (Fig. 1)

Fig. 1

Side handle

1.Loosen the side handle slightly by unscrewing it counter- clockwise.

2.Rotate the side handle to the required angle.

3.Tighten the side handle securely.

Installing Bits and Chisels (Fig. 2)

SDS Max Drive System (Cat. No. 5314-21)

The 5314-21 Rotary Hammer uses SDS max drill bits and hammer steel chisels.

Fig. 2

1.Insert the bit or chisel into the nose of the tool.

2.Rotate bit slowly until it aligns with the locking mechanism.

3.Push bit into tool until it locks.

4.Check to see that bit is locked by tugging on it.

5.To remove bits and chisels, pull bit release collar (1) toward the rear of tool and remove bit.

NOTE: Use caution when handling hot bits and chisels.

Installing Bits and Chisels (Fig. 3)

Spline Drive System (Cat. No. 5318-21)

The 5318-21 Rotary Hammer uses carbide bits with spline shanks and hammer steel chisels with round hex shanks.

Fig. 3

1

Rotary bit with spline shank

Chisel with round hex shank

1.Insert the bit or chisel into the nose of the tool.

If you are using a rotary bit, make sure that the splines on the shank engage with the splines inside the nose of the tool.

If you are using a chisel, make sure that the notch in the shank faces up (Fig. 3).

2.Push bit into tool until it locks.

3.Check to see that bit is locked by tugging on it.

4.To remove bits and chisels, pull bit release collar (1) toward the rear of tool and remove bit.

NOTE: Use caution when handling hot bits and chisels.

1

Bit with SDS max shank

page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operators Manual Electrical Safety Tool USE and Care General Safety Rules Read and Understand ALL InstructionsPersonal Safety ServiceFunctional Description Specific Safety RulesExtension Cords GroundingInstalling Bits and Chisels Fig Spline Drive System Cat. No Tool AssemblyOperation Using LHS Rotary Percussion Core Bits Fig Bushing Tools Chiseling and ChippingMortar Cutting Chisels Seam Tools Bull PointsAccessories MaintenanceFive Year Tool Limited Warranty RepairsSécurité Électrique Conservez CES Instructions Aire DE TravailUtilisation ET Entretien DES Outils Sécurité DES Personnes RéparationDescription Fonctionnelle Règles DE Sécurité ParticulièresPièce 120 385 400 40 mm 152 mm 16 mmMise À LA Terre Avertissement Calibres minimaux recommandés pour les Cordons de rallongeCordons DE Rallonge Directives pour l’emploi des cordons de rallongePositionnement de la poignée latérale Fig Montage DE Loutil AvertissementManiement Utilisation des carottiers LHS à percussion et rotation Fig Utilisation de carottiers percutants FigAvertissement Boucharde Cisellement et burinageCiseau à mortier outil à joint Ciseau à pointe robusteAccessoires Avertissement Maintenance AvertissementGarantie Limitée DE L’OUTIL DE Cinq ANS RéparationsSeguridad Electrica Guarde Estas Instrucciones Area DE TrabajoSeguridad Personal USO Y Mantenimiento DE LA HerramientaDescripción Funcional ServicioReglas Especificas DE Seguridad Guías para el uso de cables de extensión Tierra ¡ADVERTENCIAExtensiónes Eléctricas Cómo ajustar la posición de la mango lateral Fig Ensambaje DE LA Herramienta ¡ADVERTENCIAOperacion Page Page Martelinas Cincelado y corteCinceles con punta Cinceles en fríoAccesorios ¡ADVERTENCIA Mantenimiento ¡ADVERTENCIAGarantía Limitada DE Cinco Años Mantenimiento de las herramientasUnited States
Top Page Image Contents