Miller Electric Millermatic 350, 350, 350P manual Setting Crater Fill

Page 39

.A complete Parts List is available at www.MillerWelds.com

5-6. Setting Crater Fill

.Crater parameters are welding gun independent (i.e. crater fill can be on for a spool

gun and off for a MIG gun). When using the same welding gun, MIG and pulse pro- grams are independent of each other; however, crater parameters will be the same for all pulse programs. For example, if a MIG gun is using the .035 steel pulse pro- gram, and crater fill is on and parameters are set, crater will also be on and the same parameters will be set for a stainless pulse program.

1

2

3

Ref. 213 935-A

 

 

To set Crater Fill, select a program and press SETUP (1) until the TIMERS LED turns on. Press SETUP again and the left

display will show CRTR and the right display

will show OFF.

Rotate right knob (3) to turn crater ON. Rotate left knob (2) to change display to

WFS, and rotate right knob (3) to set crater wire feed speed. Wire feed speed range is 50-700 IPM (see Section 5-7).

Rotate left knob (2) to change display to TIME, and rotate right knob (3) to set crater time. Time range is 0.1-5.0 seconds (see Section 5-7).

Rotate left knob (2) to change display to VOLT (MIG program) or ARCL (pulse program), and rotate right knob (3) to set either volts (range is 10.0-32.0 volts) or arc length [range is 0-99 (see Section 5-7)].

Rotate left knob (2) to change display to TDLY for time delay. This setting is for spot or skip welding without crater fill if the arc time is less than the set time. Time range is 0.0-5.0 seconds (i.e. if TDLY is set for 2.0 seconds, weld operation will not go into crater if gun trigger is released before 2.0 seconds).

To exit this menu, press the SETUP (1) button.

OM-1327 Page 35

Image 39
Contents File MIG Gmaw OM-1327Processes DescriptionFrom Miller to You Table of Contents − Programming − Maintenance &TROUBLESHOOTINGHOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationSymboles utilisés UNE Décharge Électrique peut entraîner la mortIndique des instructions spécifiques DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLOProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-1327 Duty Cycle And Overheating SpecificationsVolt-Ampere Curve Connecting To Weld Output TerminalsInstalling Welding Gun/Cable Holder Installing Work ClampInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun Be sure to trim liner to proper extension Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProGun End Gun Liner Wire Outlet Guide XR Edge guns prior to serial noSetting Gun Polarity For Wire Type Polarity Changeover Information11/16 Rear Panel Installing Gas SupplyMin Input Conductor Size In AWG Installing Wire Spool and Adjusting Hub TensionElectrical Service Guide Input VoltageSelecting Input Voltage 200/230/460 Volt Models Only Selecting a Location And Connecting 3-Phase Input Power 18 in 457 mm for airflowTools Needed = GND/PE Earth Ground L1L2 Selection a Location And Connecting 1-Phase Input PowerDisconnect Device Input Power Connections =GND/PE Earth GroundHold wire tightly to keep It from unraveling Threading Welding Wire For MIG Gun150 mm Pressure4321 Indicator ScaleThreading Welding Wire Through XR Guns Turn welding power source OffFor XR-A Pistol Gun Controls MIG ModeJog Mode Pulse Indicator LightPulse MIG Gun-On-Demand Pulse MIG Mode Voltage AdjustmentWeld Status MIG Gun-On-DemandMillerWelds.com Weld Parameters ForWeld Weld Parameters For Pulse ModeWeld Bead Setting OM-1327 MIG Welding ModeLow Setting High Setting Pulse MIG Welding ModeTimers Crater Fill display can be turned Rmpt − Ramp Time Setting Hot Start Aluminum Pulse Only ParametersManual Hot Start Mode To exit this menu, press the Setup 1 button OM-1327Setting Crater Fill Recommended Crater Fill Parameters Recommended Crater Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Or Reset rES Overheating Routine MaintenanceDisconnect power = Check = Change ~ = Clean = ReplaceMeasuring Input Capacitor Voltage Significant DC voltage canWorking on unit Changing Drive Roll and Wire Inlet Guide Help Displays Displays a jog wire feed speed OM-1327MM 350P Jog XXX Wire Feed SpeedHelp Tip SaveUnit is in an overheated condition see Section TroubleshootingTemperatures are within acceptable limits see -2and Connect work clamp to get good metal to metal contactOM-1327 − Electrical Diagram 224 242-B Circuit Diagram For 460V/575V Models 223 926-B Drive Roll And Wire Guide Kits Page Page Service Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact