Miller Electric System Reset Instructions for Millermatic 350P Welder

Page 42

.A complete Parts List is available at www.MillerWelds.com

5-8. System Reset

.Accessing the System Reset function will also allow access to Timer Reset (RTMR)

and Option Reset (ORST) functions. The timer reset and option reset functions are for use by factory authorized service personnel only.

Do not use the timer reset or option reset functions if they appear on the displays.

1

Ref. 213 935-A

A system reset function is available that completely resets unit back to all the original factory settings.

To access this menu, turn on welding power source, then press the SETUP (1) button when the SETUP light illuminates under the Left display.

SRST will appear on the left display and OFF will appear on the right display.

To prepare the unit for system reset, rotate right knob until ON appears on the right display.

To apply the system reset function, press SETUP (1) button, and wait until unit completely reboots before performing any other operations.

OM-1327 Page 38

Image 42

Contents Description OM-1327Processes File MIG GmawFrom Miller to You Table of Contents − Maintenance &TROUBLESHOOTING − ProgrammingElectric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burnsWelding can cause fire or explosion Fumes and Gases can be hazardousARC Rays can burn eyes and skin Flying Metal or Dirt can injure eyesFalling Unit can cause injury Welding Wire can cause injuryFire or Explosion hazard Moving Parts can cause injuryEMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings About Implanted Medical DevicesSymboles utilisés UNE Décharge Électrique peut entraîner la mortIndique des instructions spécifiques DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion Risque D’INCENDIE OU D’EXPLO LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées LA Chute DE L’APPAREIL peut blesserProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-1327 Specifications Duty Cycle And OverheatingConnecting To Weld Output Terminals Volt-Ampere CurveInstalling Work Clamp Installing Welding Gun/Cable HolderInstalling Welding Gun Connecting Spoolmatic 15A Or 30A Gun XR Edge guns prior to serial no Connecting XR Edge, XR-A Gun, XR-A Python, Or XR Aluma-ProGun End Gun Liner Wire Outlet Guide Be sure to trim liner to proper extensionSetting Gun Polarity For Wire Type Polarity Changeover Information11/16 Installing Gas Supply Rear PanelInput Voltage Installing Wire Spool and Adjusting Hub TensionElectrical Service Guide Min Input Conductor Size In AWGSelecting Input Voltage 200/230/460 Volt Models Only Selecting a Location And Connecting 3-Phase Input Power 18 in 457 mm for airflowTools Needed = GND/PE Earth Ground =GND/PE Earth Ground Selection a Location And Connecting 1-Phase Input PowerDisconnect Device Input Power Connections L1L2Threading Welding Wire For MIG Gun Hold wire tightly to keep It from unravelingPressure4321 Indicator Scale 150 mmThreading Welding Wire Through XR Guns Turn welding power source OffFor XR-A Pistol Gun Pulse Indicator Light MIG ModeJog Mode ControlsMIG Gun-On-Demand Pulse MIG Mode Voltage AdjustmentWeld Status Pulse MIG Gun-On-DemandWeld Parameters For MillerWelds.comWeld Parameters For Pulse Mode WeldMIG Welding Mode Weld Bead Setting OM-1327Pulse MIG Welding Mode Low Setting High SettingTimers Crater Fill display can be turned To exit this menu, press the Setup 1 button OM-1327 Setting Hot Start Aluminum Pulse Only ParametersManual Hot Start Mode Rmpt − Ramp TimeSetting Crater Fill Recommended Crater Parameters Recommended Crater Fill Parameters19ga 20ga 05mm 0.9mm System Reset Motor Calibration Function Set Up Push Motor Torque SUP Or Reset rES = Check = Change ~ = Clean = Replace Routine MaintenanceDisconnect power OverheatingMeasuring Input Capacitor Voltage Significant DC voltage canWorking on unit Changing Drive Roll and Wire Inlet Guide Displays a jog wire feed speed OM-1327 Help DisplaysTip Save Jog XXX Wire Feed SpeedHelp MM 350PConnect work clamp to get good metal to metal contact TroubleshootingTemperatures are within acceptable limits see -2and Unit is in an overheated condition see SectionOM-1327 − Electrical Diagram 224 242-B Circuit Diagram For 460V/575V Models 223 926-B Drive Roll And Wire Guide Kits Page Page Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s