Miller Electric ICE-27T, 375 X-TREME manual Connecting 1-Phase Input Power For 240 VAC

Page 17

.A complete Parts List is available at www.MillerWelds.com

4-10. Connecting 1-Phase Input Power For 240 VAC

1

YInstallation must meet all National and Local Codes − have only qualified persons make this installation.

5

7

4

6

L1

L2

2

3

=GND/PE Earth Ground

1

YDisconnect and lockout/tagout input power before connecting input conductors from unit.

YAlways connect green or green/ yellow conductor to supply grounding terminal first, and never to a line terminal.

1Black And White Input Conductor (L1 And L2)

2Green Or Green/Yellow Grounding Conductor

3Input Power Cord.

4Disconnect Device (switch shown in the OFF position)

5Disconnect Device Grounding Terminal

6Disconnect Device Line Terminals

Connect green or green/yellow grounding conductor to disconnect device grounding terminal first.

Connect input conductors L1 and L2 to disconnect device line terminals.

8
L2	L1

240 VAC, 1

7 Over-Current Protection

Select type and size of over-current protection using Section 4-8(fused disconnect switch shown).

8Receptacle (NEMA 6-50R) Customer Supplied

Close and secure door on disconnect device. Remove lockout/tagout device, and place switch in the On position.

Tools Needed:

803 766-B / Ref. 802 443-A

OM-225 216 Page 13

Image 17

Contents Processes OM-225 216FDescription File Plasma CuttersFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsagePlasma Arc Cutting Hazards Cutting can cause fire or explosionFlying Sparks can cause injury Exploding Parts can injureARC Rays can burn eyes and skin Noise can damage hearingCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information LE Coupage présente un risque de feu ou d’explosion Signification des symbolesUNE Décharge Électrique peut entraîner la mort Identifie un message de sécurité particulierLE Bruit peut endommager l’ouïe Risque de blessure en casLES Fumées ET LES GAZ peuvent être dangereux LE Plasma D’ARC peut entraîner des blessuresDES Organes Mobiles peuvent provoquer des blessures DES Pieces Chaudes peuvent pro- voquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OUInformation sur les champs électromagnétiques Principales normes de sécuritéLE Coupage Ã L’ARC peut causer des interférence Consignes relatives aux stimulateurs cardiaquesSpecifications For Torch Symbols And DefinitionsSpecifications Duty Cycle And Overheating Power Source Dimensions And WeightTorch Dimensions And Weight Connecting Work Clamp Connecting Gas/Air SupplyExtension Cord Data Electrical Service Guide For 240 VAC60 Hz Input Voltage 240 Input Amperes At Rated OutputConnecting 1-Phase Input Power For 240 VAC 460 mm Connecting Input PowerControls − OperationCutting Speed Trigger Safety LockSequence Of Operation When trigger is pressedExample Of Cutting Operation Pilot arc starts immediatelyOverload Protection Routine MaintenanceTurn Off Wrapper RemovalWrapper Check Bus Removing wrapper Wrapper Torx Screws Fine ThreadDC Bus Voltage Check Checking Or Replacing Filter Element Shield Cup Checking Torch Shield Cup Shutdown SystemChecking/Replacing Retaining Cup, Tip, And Electrode Turn Off power source before checking torch partsWork Cable Connections Torch And Work Cable ConnectionsTorch Connections OM-225 216 − Electrical Diagram 224 682-B Recommended Spare Parts Recommended Spare PartsOM-225 216 Page Support ServiceMiller Electric Mfg. Co Owner’s Record