Miller Electric and DS-75D16, DS-75S16, DS-75S12 Installing Wire Guide Extension, Installing Guard

Page 15

4-4. Installing Wire Guide Extension

1

 

1

Wire Guide Fitting

 

2

Bolt

 

3

Monocoil Liner

 

4

Wire Guide Extension

4

Tighten bolt to secure liner in wire

guide fitting. Do not overtighten bolt

 

3

and crush liner.

 

Repeat procedure for opposite

2

 

 

side.

 

 

Tools Needed:

3/8 in

ST-152 383

4-5. Installing Guard

1 Motor Mounting Bracket

2 Mounting Screws

Remove 4-screws from motor mounting bracket.

3 Guard

Secure guard using 4 screws pre- viously removed. For standard speed motor mount guard use mounting holes as shown.

1

This illustration shows the mounting screws in place for a standard speed motor. The remaining holes are used for low speed motors.

2

Tools Needed:

3

3/8 in

804 783-A

OM-230 300 Page 11

Image 15
Contents File MIG Gmaw OM-230 300AProcesses DescriptionFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéRating SpecificationsInstalling Swivel Into Pipe Post Do not remove Safety Collar until instructed toInstalling Boom And Reel Support Installing Control Box And Adjusting TiltInstalling Guard Installing Wire Guide ExtensionEquipment Connection Diagram Control Box Connections Pin Plug InformationPin Information Gun Recommendation Table Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityRemoval Installing Drive RollsDrive Roll Carrier Ejector Button Pressure Door Assembly InstallationInstalling PD continuous wire guides with PD drive rolls Installing PD Continuous Wire GuidesInstalling wire guides with non- PD old- style drive rolls Installing Non-PD Old Style Wire GuidesInstalling gun without Accu-Mate con- nection Installing Welding GunInstalling gun without Installing gun with Accu-Mate connec- tionCut wire off To adjust drive roll pressure, hold nozzleSettings When installing gun, the liner should extend Install gun. Lay gun cable out straight. Cut off AboveLeft Side Motor Control Board PC101 Right Side Motor Setting Internal DIP Switches On Motor BoardsRun-In Disabled S1-1 Manually Adjusted Run-In S1-1 And S1-2Digital Meter DIP Switch Setting Equipment DIP Switch Settings For Models With Meters OnlyPower Switch Left/Right Select SwitchJog/Purge Voltage Controls Trigger Hold SwitchTrigger Hold Switches Voltage Control And Digital Meters= Check ~ = Clean = Replace Reference Every Routine MaintenanceBrush Inspection And Replacement Disconnect power before maintainingDiagnostics Troubleshooting Disconnect power before troubleshootingTrouble Remedy OM-230 300 − Electrical Diagram 204 716-B − Parts List Quantity Control Box 193 Knob, Pointer 1.250 Dia x .250 Id W/Two Set Screws Harness Connectors/ReceptaclesBoom Assembly Boom Assembly -1 Item See -1 For Drive Roll & Wire Guide KitsDrive Assembly With Motor Left Side Shown Support, Hub & Reel PD-V Page Page Page Service Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact