Miller Electric DS-75S12, DS-75S16 manual Equipment DIP Switch Settings For Models With Meters Only

Page 25

4-18. Equipment DIP Switch Settings (For Models With Meters Only)

		Remove wrapper.
		1 DIP Switch S2 On Digital
		Meter Board PC60
		Install wrapper when finished.
Digital Meter DIP Switch Setting
1
	Inches/Minute	Meters/Minute
	5	5
	4	4
	3	3
	2	2
PC60	1	1
		Tools Needed:
		1/4 in
		Ref. 803 154 / 803 188

OM-230 300 Page 21

Image 25

Contents Processes OM-230 300ADescription File MIG GmawFrom Miller to You Table of Contents Page Marks a special safety message Symbol UsageArc Welding Hazards Electric Shock can killWelding can cause fire or explosion ARC Rays can burn eyes and skinFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier Incendie ou une explosion LE Soudage peut provoquer unDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesLA Chute DE L’APPAREIL peut blesser Risque D’INCENDIE OU D’EXPLO’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques Principales normes de sécuritéInstalling Swivel Into Pipe Post SpecificationsDo not remove Safety Collar until instructed to RatingInstalling Boom And Reel Support Installing Control Box And Adjusting TiltInstalling Guard Installing Wire Guide ExtensionEquipment Connection Diagram Pin Plug Information Control Box ConnectionsPin Information Wire Type, Size, And Feed Speed Capability Table Removing Safety Collar And Adjusting BoomMotor Speed Wire Type Wire Size Feed Speed Capability Gun Recommendation TableDrive Roll Carrier Ejector Button Pressure Door Assembly Installing Drive RollsInstallation RemovalInstalling PD continuous wire guides with PD drive rolls Installing PD Continuous Wire GuidesInstalling wire guides with non- PD old- style drive rolls Installing Non-PD Old Style Wire GuidesInstalling gun without Installing Welding GunInstalling gun with Accu-Mate connec- tion Installing gun without Accu-Mate con- nectionSettings When installing gun, the liner should extend To adjust drive roll pressure, hold nozzleInstall gun. Lay gun cable out straight. Cut off Above Cut wire offRun-In Disabled S1-1 Setting Internal DIP Switches On Motor BoardsManually Adjusted Run-In S1-1 And S1-2 Left Side Motor Control Board PC101 Right Side MotorDigital Meter DIP Switch Setting Equipment DIP Switch Settings For Models With Meters OnlyLeft/Right Select Switch Power SwitchJog/Purge Trigger Hold Switches Trigger Hold SwitchVoltage Control And Digital Meters Voltage ControlsBrush Inspection And Replacement Routine MaintenanceDisconnect power before maintaining = Check ~ = Clean = Replace Reference EveryDiagnostics Disconnect power before troubleshooting TroubleshootingTrouble Remedy OM-230 300 − Electrical Diagram 204 716-B − Parts List Quantity Control Box 193 Knob, Pointer 1.250 Dia x .250 Id W/Two Set Screws Harness Connectors/ReceptaclesBoom Assembly Boom Assembly -1 Item See -1 For Drive Roll & Wire Guide KitsDrive Assembly With Motor Left Side Shown Support, Hub & Reel PD-V Page Page Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s