Miller Electric D-74DX manual Drive rolls can injure fingers, Keep your head out of the fumes

Page 15

SECTION 3 − DEFINITIONS

3-1. Warning Label Definitions

ABC

1

1.1

1.2

1.3

2			2.1			2.2			2.3

3

3.1

3.2

3.3

4	4.1
	+	+ +
5	+	6
	+

S-178 936

A.Warning! Watch Out! There are possible hazards as shown by the symbols.

B.Drive rolls can injure fingers.

C.Welding wire and drive parts are at welding voltage during operation − keep hands and metal objects clear.

1 Electric shock can kill.

1.1Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves.

1.2Protect yourself from electric shock by insulating yourself from work and ground.

1.3Disconnect input plug or power before working on machine.

2Breathing welding fumes can be hazardous to your health.

2.1Keep your head out of the fumes.

2.2Use forced ventilation or local exhaust to remove the fumes.

2.3Use ventilating fan to remove fumes.

3Welding sparks can cause explosion or fire.

3.1Keep flammables away from welding. Don’t weld near flammables.

3.2Welding sparks can cause fires. Have a fire extinguisher nearby and have a watch person ready to use it.

3.3Do not weld on drums or any closed containers.

4Arc rays can burn eyes and injure skin.

4.1Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.

5Become trained and read the instructions before working on the machine or welding.

6Do not remove or paint over (cover) the label.

OM-1500-7 Page 11

Image 15

Contents File MIG Gmaw OM-1500-7 204 129HProcesses DescriptionFrom Miller to You Table of Contents Decwire6/05 DirectivesStandards HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationSymboles utilisés UNE Décharge Électrique peut entraîner la mortIndique des instructions spécifiques DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionProposition californienne 65 Avertissements LES Fils DE Soudage peuvent provoquer des blessuresLE Soudage À L’ARC risque de provoquer des interférences Principales normes de sécurité Information EMFEn ce qui concerne les implants médicaux OM-1500-7 Disconnect input plug or power before working on machine Drive rolls can injure fingersKeep your head out of the fumes Weee Label For Products Sold Within The EU Symbols And DefinitionsSome symbols are found only on CE products Rating Label For CE ProductsSpecifications Site SelectionRating Equipment Connection Diagrams Shielding gas pressure not toExceed 100 PSI 689 kPa Rear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Pin Plug InformationMent above.Cut wire off. Close cover Installing And Threading Welding WirePosition Settings And Results For DIP Switch S1 Setting Internal DIP SwitchesDIP Switch S1 DIP Switch S4 Not For Customer Use When DIP switch positions are changed,Power Source Selection Menu Power Switch Left/Right Select SwitchOperational Terms Jog/Purge Switch Wire Speed Front Panel ControlsTime sec CE Models Program Push ButtonUpper Display Non-CE ModelsLower Display Setup Push ButtonAdjust Control Time Welding Sequence DiagramSequence Push Button Upper Display Setup Push ButtonAuxiliary Menus Sequence Push ButtonWire Feed Speed Units Reset To Factory SettingsPower Source Selection Menu Trigger Hold SetupDisplay Hold Software Revision LevelCode Optional Dual Schedule Switch Diagrams Sequence Parameters In a ProgramFor more information on Sequence Push Button see Section There is a two-position DIP DiagnosticsError LED3-Related Error IndicationsDiagnostics For User Defined Options Routine MaintenanceMonths Pull TroubleshootingDisconnect power before troubleshooting Trouble RemedyOM-1500-7 − Electrical Diagram 204 144-C − Parts List Part Description Quantity Control Box PLG117 165 Harness Connectors/ReceptaclesHardware is common Not available unless listed See -1 For Drive Roll & Wire Guide Kits21 . PC51,151 201 Roll Drive Kit Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll DriveService Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact