Miller Electric D-74DX manual Power Source Selection Menu

Page 23

5-9. Power Source Selection Menu

Non-CE Model Shown

1

Program

Volts

Time (sec)

 

 

Wire Speed

Amps

Start

 

 

2

 

 

 

Crater

 

 

Trigger Hold

Pre/Postflow

 

 

Dual Schedule

SequenceAdjustSetup

* * Power Source

Upper Display

Lower Display

Voltage Range

 

 

 

 

 

Deltaweld 452

dELT

452

Vmin =10

Vmax =38

Deltaweld 302

dELT

302

Vmin =10

Vmax =32

Deltaweld 652

dELT

652

Vmin =10

Vmax =44

Dimension 302

dIM

302

Vmin =10

Vmax =32

Dimension 452

dIM

452

Vmin =10

Vmax =38

Dimension 652

dIM

652

Vmin =10

Vmax =65

 

 

 

 

 

Dimension 1000

dIM

1000

Vmin =10

Vmax =60

 

 

 

 

 

XMT 304

XMT

304

Vmin =10

Vmax =35

 

 

 

 

 

XMT 456

XMT

456

Vmin =10

Vmax =38

 

 

 

 

 

Invision 354MP

I354

MP

Vmin =10

Vmax =35

 

 

 

 

 

Invision 456MP

I456

MP

Vmin =10

Vmax =38

 

 

 

 

 

Invision 456P

I456

P

Vmin =10

Vmax =38

 

 

 

 

 

PHOENIX 456

PHX

456

Vmin =10

Vmax =38

 

 

 

 

 

SUMMITARC 1000

SUM

1000

Vmin =25

Vmax =44

 

 

 

 

 

 

 

 

 

 

**For any power sources not listed, pick a matching voltage range, or see Sec 5-12 to set Vmin and Vmax.

1Upper Display

2Lower Display

.When the feeder is turned on,

the Power Source Selection Menu allows the operator to se- lect a default power source. Selecting a default power source, automatically sets the correct Vmin and Vmax set- tings for adjusting the output voltage of the power source.

First Time Feeder Is Turned On

The feeder automatically goes into the Power Source Selection Menu. The feeder displays “dELT” on the Upper Display and “452” on the Lower Display, meaning that a Del- taweld 452 is the default power source, and has a voltage range of 10V as Vmin and 38V as Vmax.

At power up, the operator has three seconds to select a default power source from the list shown on the display. Operator may scroll through the list of power sources by using the Adjust control. After se- lecting a power source the operator has three seconds to change to a different power source or begin welding. After making a power source selection, the operator may press the Program Button to avoid having to wait the three seconds. When turning off the feeder, the de- fault power source will be retained.

If voltage settings have already been set with the Vmin and Vmax in the Auxiliary Menu, selecting a de- fault power source with the Power Source Selection Menu overrides the Vmin and Vmax voltage set- tings.

Next Time Feeder Is Turned On

The feeder will display the last se- lected default power source. The operator has three seconds to se- lect another power source, or press the Program Button to exit the Pow- er Source Selection Menu.

Disabling The Power Source Selection Menu

Once the default power source has been selected the Power Source Selection Menu may be disabled using the Auxiliary Menus. See Section 6-12.

OM-1500-7 Page 19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents File MIG Gmaw OM-1500-7 204 129HProcesses DescriptionFrom Miller to You Table of Contents Standards Decwire6/05Directives HOT Parts can cause severe burns Symbol UsageArc Welding Hazards Electric Shock can killFlying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosionMoving Parts can cause injury Welding Wire can cause injuryFire or Explosion hazard Falling Unit can cause injuryAbout Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF InformationIndique des instructions spécifiques Symboles utilisésUNE Décharge Électrique peut entraîner la mort LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux LA Chute DE L’APPAREIL peut blesser LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU D’EXPLO- SionLE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLES Fils DE Soudage peuvent provoquer des blessures En ce qui concerne les implants médicaux Principales normes de sécuritéInformation EMF OM-1500-7 Keep your head out of the fumes Disconnect input plug or power before working on machineDrive rolls can injure fingers Weee Label For Products Sold Within The EU Symbols And DefinitionsSome symbols are found only on CE products Rating Label For CE ProductsRating SpecificationsSite Selection Exceed 100 PSI 689 kPa Equipment Connection DiagramsShielding gas pressure not to Rear Panel Connections And Rotating Drive Assembly Gun Recommendation Table Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Pin Plug InformationMent above.Cut wire off. Close cover Installing And Threading Welding WirePosition Settings And Results For DIP Switch S1 Setting Internal DIP SwitchesDIP Switch S1 DIP Switch S4 Not For Customer Use When DIP switch positions are changed,Power Source Selection Menu Operational Terms Power SwitchLeft/Right Select Switch Jog/Purge Switch Time sec Wire SpeedFront Panel Controls CE Models Program Push ButtonUpper Display Non-CE ModelsLower Display Setup Push ButtonSequence Push Button Adjust ControlTime Welding Sequence Diagram Upper Display Setup Push ButtonAuxiliary Menus Sequence Push ButtonWire Feed Speed Units Reset To Factory SettingsPower Source Selection Menu Trigger Hold SetupCode Display HoldSoftware Revision Level For more information on Sequence Push Button see Section Optional Dual Schedule Switch DiagramsSequence Parameters In a Program There is a two-position DIP DiagnosticsError LED3-Related Error IndicationsMonths Diagnostics For User Defined OptionsRoutine Maintenance Pull TroubleshootingDisconnect power before troubleshooting Trouble RemedyOM-1500-7 − Electrical Diagram 204 144-C − Parts List Part Description Quantity Control Box PLG117 165 Harness Connectors/ReceptaclesHardware is common Not available unless listed See -1 For Drive Roll & Wire Guide Kits21 . PC51,151 201 Roll Drive Kit Drive Roll And Wire Guide Kits Fraction MetricKit Roll Wire Size Roll DriveSupport ServiceYour distributor also gives Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact
Top Page Image Contents