Installation

NOTE: Installation of a low pressure safety cutoff switch on the pump discharge is recommended (and may be required by your local code) to shut off the power in case of low discharge pressure (caused by broken pipe, etc.).

2.Mount the pump on a solid base in the location you have decided on.

3.Choose a time that will allow you to shut off the water to the household while you install the Ace-In- The-Hole Automatic Booster Pump.

4.Shutoff the main water supply valve to the household.

5.Open any faucet to relieve water pressure in the plumbing. Once the water pressure is relieved, close the faucet.

6.READ STEP 6 COMPLETELY BEFORE STARTING TO WORK ON IT. You must remove a length of pipe from the main water supply line to allow installation of elbows for the Ace-In-The-Hole Automatic Booster Pump. The locations of the cuts must take into con- sideration the size of the elbows being used, the length of the threads in threaded joints or the overlap in glued or soldered joints, etc.. Position the elbows in line with the pump suction and discharge threads. There may be some water leakage while cutting the pipe. Remove any burrs or shavings caused by the cutting tool.

NOTE: Galvanized pipe may not need to be cut. If there is a union close to the pump location, dis- assemble the union and remove (unscrew) pipe back past the pump location. Have new lengths of pipe cut and threaded to allow for the pump installation.

NOTE: Both female suction and male discharge ports have 1” NPT threads. Depending on your type of connection and the size of your home’s piping, you may need to install adapters on the ports.

7.Once the short piece of pipe is removed, the piping above the cut can be drained to prevent water mess. Place a pail under the opening going to the house- hold. Open the highest faucet in the system to let in air so the water can fall out of the pipes into the pail. Once it’s drained, close the faucet.

8.Install the elbows in the main water supply line. Point them toward the pump.

Risk of burst hose and flooding. Do not install with flexible hoses. Use only rigid piping that meets code.

9.Install piping from elbows to pump including a union in each line, an elbow in the discharge line, and a check valve in the pump suction line. The arrow on the check valve must point to the pump suction (see Figure 2). If not already in the plumbing system, install a pressure relief valve in the pump discharge line capable of passing the full pump flow at 100 psi (689 kPa). If local code requires installation of a pres- sure relief valve capable of handling the full pump flow at a pressure less than 100 psi (689 kPa), follow the code requirements. A low pressure safety cutoff switch should also be installed in the discharge line, and may be required by your local codes.

10.With all pipe and fittings installed and sealed, turn on the main water supply slowly to pressurize the system and check for leaks. If any leaks appear, turn the main valve off, open a faucet to relieve the pressure, and repair the leak. Repeat this step until there are no leaks in the system.

11.Open a faucet to release the air from the pipes and allow water to flow. When a steady stream of water flows out of the faucet, the pump is full of water and fully primed. Close the faucet.

12.Before continuing with the installation, see the sections of this manual titled “Electrical Connections”, “Automatic Pressure Controller”, “Normal Operation”, and “When Does The Pump Stop Operating” for detailed information on how the system functions.

13.At this point, you can plug in the pump for the first time. When you plug in the power cord, the pump will start and run for a few seconds.

14.When the pump stops running (after it shuts off auto- matically), the system is at the boosted pressures. Inspect the pipe and fittings again for water leaks. If any leaks appear, unplug the pump, turn the water main valve off, open a faucet to relieve the pressure and repair the leak. Repeat this step until there are no leaks in the system.

Household

Water
Supply In	5601 0807

Figure 3:Typical bypass piping needed to allow removal of pump for repair without shutting down household water system.

For parts or assistance, call Simer Customer Service at 1-800-468-7867

3075SS-01 specifications

Simer Pumps has established a reputation for high-quality, reliable water movement solutions, and the Simer Pumps 3075SS-01 model is a prime example of this commitment to excellence. Designed for both residential and commercial applications, the 3075SS-01 is a submersible utility pump that caters to a diverse array of pumping needs, including draining flooded basements, emptying swimming pools, and managing groundwater.

One of the standout features of the 3075SS-01 is its robust construction, which includes a stainless steel housing. This not only enhances its durability but also ensures resistance to corrosion, making it an ideal choice for prolonged use in harsh environments. The pump is designed to handle various water types, including clean water and those with small particles suspended in them, making it versatile for different pumping applications.

Equipped with a powerful motor, the Simer 3075SS-01 can deliver an impressive flow rate. This efficiency means that it can quickly remove water, significantly reducing the time needed for draining tasks. The pump’s maximum pumping capacity reaches around 3,300 gallons per hour, with an impressive head height, allowing it to move water effectively from deeper spaces.

The 3075SS-01 also boasts an automatic float switch, which activates the pump when water levels rise beyond a certain point. This feature ensures that the pump operates without the need for manual intervention, providing peace of mind for users who may be away from the pump while it operates. Additionally, the float switch is adjustable, enabling users to set the operational range according to specific needs.

Another characteristic that enhances the versatility of the Simer 3075SS-01 is its compact and lightweight design. This enables easy handling and transportation, allowing users to position the pump conveniently in different locations as needed. The built-in handle further facilitates easy transport, making it user-friendly for both professionals and DIY enthusiasts.

Overall, Simer Pumps' 3075SS-01 model combines powerful performance with reliable construction and user-friendly features, making it an excellent choice for anyone in need of an efficient and durable submersible utility pump. With its advanced technologies and thoughtful design, this pump stands out for its ability to handle a variety of water movement tasks with ease, ensuring reliability when it matters most.