Simer Pumps Complete Guide for Troubleshooting and Servicing Your Water Pump
Page 7

Operation / Service / Troubleshooting

7

Restart: Make sure that the suction line is not obstructed, and that it is connected to a water source.

•Press and hold the ‘Restart’ button for 5 seconds.

•The ‘Pump on’ LED should light up, and

•The ‘Failure’ LED should go off.

If flow is adequate, the pump will operate until sev- eral seconds after it reaches the set-point pressure and the flow stops.

LUBRICATION

The motor is lubricated at the factory for the life of the bearings. The pump seal is water cooled and self lubricating.

TROUBLESHOOTING

PUMP SERVICE

Hazardous voltage. Can shock, burn, or cause death. Unplug the pump and controller before servicing them. Do not handle the pump or controller or attempt to work on the pump with wet hands or while standing on a wet or damp floor.

The motor has an auto-reset thermal overload protector. If the motor overheats, the overload will cut off the power to prevent damage and will reset after the motor cools. If the overload trips repeatedly, check the pump for the cause (low voltage, a clogged impeller, etc.).

SYMPTOM

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

Motor will not run

Fuse is blown or circuit breaker tripped

DISCONNECT POWER; Replace fuse or reset circuit breaker.

 

Power cord not plugged in

Plug into 115 Volt grounded outlet.

 

 

 

Motor runs hot and

Voltage is too low

Check voltage being supplied to pump.

overload kicks off or

Impeller not moving freely

Check that impeller moves freely and is not clogged.

motor does not run

 

 

and only hums

 

 

Motor runs but no

Improper priming

Re-prime according to instructions.

water is delivered*

Clogged water filter

Stop pump, shut off water, and change filter cartridge. Filter should be

* (Note: Unplug

 

installed on discharge side of pump.

Discharge valve closed

Open valve.

pump; then open

Pipe size too small

Re-pipe using pipe of the same size as suction and discharge ports on pump.

faucets and see if

water is flowing

Impeller is plugged

Clean impeller.

through system).

Pipes are frozen

Thaw pipes.

 

 

 

 

*Pump does not

Corroded pipes

Replace with plastic or new steel pipe.

deliver water to full

Piping is too small in size

Re-pipe using pipe the same size as suction and discharge ports on pump.

capacity

Pump not being supplied with

Enlarge inlet pipe; check well pump system.

 

 

enough water

 

 

Low voltage

Make sure outlet is at 115 Volts.

 

 

 

For parts or assistance, call Simer Customer Service at 1-800-468-7867

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Bomba automática de refuerzo Installation/Operation/PartsAutomatic Booster Pump AutomatiqueElectrical Safety SafetyRead and Follow Safety Instructions General SafetyTable of Contents Installation General Information / InstallationGeneral Information Installation Automatic Pressure Controller Installation / OperationWhen does the Pump Stop OPERATING? Electrical ConnectionTroubleshooting Pump Service Operation / Service / TroubleshootingLubrication Model 3075SS-01 Repair PartsKey Part 3075SS-01 Description Laver. Ne pas l’immerger. Le protéger contre la pluie Ce symbole indique qu’il faut être prudent. Lorsque ceSécurité Consignes DE Sécurité GénéralesAttacher LE Reçu Dorigine ICI À DES Fins DE Garantie Table des matièresRenseignements Généraux Renseignements généraux et InstallationArrivée Water ’eauSupply Quand LA Pompe CESSE-T-ELLE DE FONCTIONNER? Installation et fonctionnementBranchements Électriques ServorégulateurLubrification Fonctionnement, entretien et dépannageDépannage Entretien DE LA Pompe Des pièces Qté Pièces de rechangeModèle 3075SS-01 Désignation 3075SS-01Instrucciones Generales DE Seguridad SeguridadEste es el símbolo de alerta de seguridad. Cuando vea Página ÍndiceInformación General Información general / InstalaciónInstalación Riesgo de explosión de la manguera y de Instalación¿CUÁNDO Deja DE Funcionar LA BOMBA? Instalación / OperaciónConexiones Eléctricas Controlador Automático DE PresiónLubricación Operación / Servicio / Localización de fallasLocalización DE Fallas Servicio DE LA Bomba Modelo 3075SS-01 Repuestos para la reparaciónClave Descripción 3075SS-01 De la pieza

3075SS-01 specifications

Simer Pumps has established a reputation for high-quality, reliable water movement solutions, and the Simer Pumps 3075SS-01 model is a prime example of this commitment to excellence. Designed for both residential and commercial applications, the 3075SS-01 is a submersible utility pump that caters to a diverse array of pumping needs, including draining flooded basements, emptying swimming pools, and managing groundwater.

One of the standout features of the 3075SS-01 is its robust construction, which includes a stainless steel housing. This not only enhances its durability but also ensures resistance to corrosion, making it an ideal choice for prolonged use in harsh environments. The pump is designed to handle various water types, including clean water and those with small particles suspended in them, making it versatile for different pumping applications.

Equipped with a powerful motor, the Simer 3075SS-01 can deliver an impressive flow rate. This efficiency means that it can quickly remove water, significantly reducing the time needed for draining tasks. The pump’s maximum pumping capacity reaches around 3,300 gallons per hour, with an impressive head height, allowing it to move water effectively from deeper spaces.

The 3075SS-01 also boasts an automatic float switch, which activates the pump when water levels rise beyond a certain point. This feature ensures that the pump operates without the need for manual intervention, providing peace of mind for users who may be away from the pump while it operates. Additionally, the float switch is adjustable, enabling users to set the operational range according to specific needs.

Another characteristic that enhances the versatility of the Simer 3075SS-01 is its compact and lightweight design. This enables easy handling and transportation, allowing users to position the pump conveniently in different locations as needed. The built-in handle further facilitates easy transport, making it user-friendly for both professionals and DIY enthusiasts.

Overall, Simer Pumps' 3075SS-01 model combines powerful performance with reliable construction and user-friendly features, making it an excellent choice for anyone in need of an efficient and durable submersible utility pump. With its advanced technologies and thoughtful design, this pump stands out for its ability to handle a variety of water movement tasks with ease, ensuring reliability when it matters most.
Top Page Image Contents