Hitachi DH 50MB instruction manual Double Insulation for Safer Operation

Page 8

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “Double insulation” means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “” or the words and “Double insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed.

Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS OF THIS TOOL!

8

Image 8
Contents Manual DE Instrucciones E Instrucciones DE Seguridad Rotary Hammer Marteau Rotatif Martillo GiratorioContents Meanings of Signal Words Important InformationSafety General Safety RulesEnglish Specific Safety Rules and Symbols Do not wipe plastic parts with solvent Double Insulation for Safer Operation Name of Parts SpecificationsFunctional Description Prior to Operation Assembly and OperationApplications Regulating the number of rotations and hammering Fig HOW to USEHow to drill holes Fig When chipping and shredding at hammering How to chisel or crush FigWhen drilling at rotation + hammering Install the stopper Fig Using Drill CHUCK, Chuck Adaptor Warming up FigHOW to USE the Core BIT MountingHow to bore Fig Dismounting FigMaintenance and Inspection How to replase grease Modifications Service and repairsService parts list Accessories Standard AccessoriesDrilling holes....For drilling metals and wooden materials Hitachi Informations Importantes Signification DES Mots D’AVERTISSEMENTConserver CES Instructions SecuriteRegles Generale DE Securite Français Manipuler l’outil correctement Regles DE Securite Specifiques ET SymbolesUtiliser l’outil correct Ne pas essuyer les parties en plastique avec du solvant Garder propres les évents d’air du moteurUtiliser l’outil motorisé à la tension nominale Double Isolation Pour UN Fonctionnement Plus SUR Remarque Description FonctionnelleNOM DES Parties Avant L’UTILISATION Precaution UtilisationRéglage du nombre de rotations et de percussion Fig Comment percer des trous FigComment buriner ou broyer Fig Perçage en rotation + percussionBurinage et découpures en percussion Moteur est à l’arrêt completInstaller la quenouille Fig Precautión AvertissementPréchauffage Fig Comment Utiliser LA Couronne Montage’assurer que l’interrupteur est sur la Position d’arrêt OFF et débrancher ’outilPerçage Fig Démontage FigEntretien ET Inspection Contrôle du foret de perçageInspection des vis de montage Entretien du moteurComment remplacer la graisse Entretien et reparation Liste des pièces de rechangeAccessoires Accessoires StandardPerçage de trous.…Pour perçage des métaux et du bois Creusage de rainures et cassure des angles Percussion Información Importante Significado DE LAS Palabras DE SeñalizaciónGuarde Estas Instrucciones SeguridadNormas Generales DE Seguridad Peligrosos cuando se utilicen con otra Maneje correctamente la herramienta Normas Y Símbolos Específicos DE SeguridadUtilice la herramienta correcta Maneje con cuidado las herramientas eléctricas No limpie las partes de plástico con disolventeAislamiento Doble Para Ofrecer UNA Operación MÁS Segura Descripción Funcional NomenclaturaEspecificaciones NotaAntes DE LA Operación Montaje Y OperaciónAplicaciones Modo DE Utilizacion Regulación de número de rotaciones Martilleo FigTaladrar orificios Fig PrecauciónPara cortar con escoplo y cincel en el modo de martilleo Forma de picar o romper FigCuando taladre con rotación + martilleo Instalar el tope Fig Advertencia Calentamiento FigModo DE Usar LA Barrena Tubular MontajeModo de taladrar Fig Desmontaje FigMantenimiento E Inspección Inspeccionar la broca de taladroInspección de los tornillos de montaje Mantenimiento de motorCambio de grasa Modificaciones Mantenimiento y reparaciónLista de repuestos Accesorios Accesorios EstándarRomper Martilleo Excavar, ranurado y rebordes Martilleo Page Page English Français Español 4MM Page Hitachi Koki Canada Co