Cisco Systems RV042RF manual GroupVPN Status, Gateway to Gateway, Client to Gateway

Page 41

Chapter 4

Advanced Configuration

Mode Choose

Gateway to Gateway

To create a tunnel between two VPN devices, such as two VPN Routers, click Add Now. The Gateway to Gateway screen appears. Proceed to the “VPN > Gateway to Gateway” section for instructions. Click Return to return to the Summary screen.

Client to Gateway

To create a tunnel between the VPN Router and the client using VPN client software that supports IPSec, click Add Now. The Client to Gateway screen appears. Proceed to the “VPN > Client to Gateway” section for instructions. Click Return to return to the Summary screen.

If the VPN Summary table has multiple pages, select a different page to view from the Jump to drop-down menu. If you want more or fewer entries listed per page, select

adifferent number from the entries per page drop-down menu.

After you have added the VPN tunnel, you will see it listed in the table.

No.  It shows the number of the VPN tunnel.

Name  It shows the Tunnel Name that you gave the VPN tunnel.

Status  This indicates the status of the VPN tunnel.

Phase2 Enc/Auth/Grp  This shows the Phase 2 Encryption type (NULL/DES/3DES/AES-128/AES-192/AES- 256), Authentication method (NULL/MD5/SHA1), and DH Group number (1/2/5) that you chose in the IPSec Setup section.

If you selected Manual for the Keying Mode in the IPSec section, then only the Encryption type and Authentication method will be displayed.

Local Group  This shows the IP address and subnet mask of the Local Group.

Remote Group  The IP address and subnet mask of the Remote Group are displayed here.

Remote Gateway  It shows the IP address of the Remote Gateway.

Tunnel Test  Click Connect to verify the status of the VPN tunnel. The test result will be updated in the Status column. If the tunnel is connected, a Disconnect button will be available so you can end the connection.

Config.  Click Edit to open a new screen where you can change the tunnel’s settings. Refer to the “Gateway to Gateway” or “Client to Gateway” section for more information. Click the Trash Can icon to delete all of your tunnel settings for each individual tunnel.

Tunnel Enabled  The number of enabled VPN tunnels is displayed.

Tunnel Defined  The number of defined VPN tunnels is displayed.

GroupVPN Status

If you do not enable the GroupVPN setting for any of your Client to Gateway tunnels, then this section will be blank.

Group Name  This shows the name you entered when you created the Client to Gateway tunnel.

Connected Tunnels  This shows the number of users logged into the group VPN.

Phase2 Enc/Auth/Grp  This shows the Phase 2 Encryption type (NULL/DES/3DES/AES-128/AES-192/AES- 256), Authentication method (NULL/MD5/SHA1), and DH Group number (1/2/5) that you chose in the IPSec Setup section.

Local Group  This shows the IP address and subnet mask of the Local Group.

Remote Client  This shows the remote clients in the group VPN.

Remote Clients Status  Click Detail List to display the Group Name, IP address and ConnectionTime of this group VPN. Click Refresh to update the on-screen information. Click Close to exit this screen and return to the Summary screen.

Tunnel Test  Click Connect to verify the status of the group VPN. The test result will be updated in the Status column. If the group VPN is connected, a Disconnect button will be available so you can end the connection.

Config.  Click Edit to open a new screen where you can change the tunnel’s settings. Refer to the “Client to Gateway” section for more information. Click the Trash Can icon to delete all of your settings for each individual group VPN.

10/100 4-Port VPN Router

34

Page 40 Page 42
Image 41
Page 40 Page 42
Contents 10/100 4-Port VPN Router About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Ddns Appendix B Linksys QuickVPN for Windows 2000, XP, or Vista Appendix a TroubleshootingAppendix H Specifications Appendix F Firmware UpgradeAppendix G Trend Micro ProtectLink Gateway Service Appendix D IPSec NAT TraversalAppendix L Contact Information Appendix I Warranty InformationAppendix K Regulatory Information Introduction ChapterChapter Introduction Computer using VPN client software to VPN Router Product Overview Chapter Product OverviewInstallation Chapter InstallationPhysical Installation Cable ConnectionsInstallation Advanced Configuration Chapter Advanced ConfigurationHow to Access the Web-Based Utility OverviewSystem Information ConfigurationPort Statistics Trend Micro ProtectLink GatewayFirewall Setting Status Network Setting StatusVPN Setting Status Log Setting StatusNetwork Setup Tab NetworkLAN Setting WAN Connection Type Dual-WAN/DMZ SettingPptp Point-to-Point Tunneling Protocol PPPoE Point-to-Point Protocol over EthernetHeart Beat Signal Setup PasswordSetup DMZ Host Setup TimePassword TimeForwarding Setup Tab ForwardingPort Range Forwarding Port TriggeringUPnP Setup UPnPSetup MAC Clone Setup One-to-One NATOne-to-One NAT Add RangeMAC Clone Setup DdnsWAN1/2 DynDNS.orgAdvanced Routing Setup Advanced RoutingDynamic Routing Oray.net PeanutHull DdnsStatic Routing Dhcp SetupStatic IP SetupDynamic IP Dhcp Status Smart Link BackupStatus Dual-WANLoad Balance Network Service DetectionProtocol Binding System Management Bandwidth ManagementBandwidth WAN1/2 Maximum Bandwidth provided by ISP Bandwidth ManagementBandwidth Management Type Rate ControlPriority System Management SnmpDiagnostic System Management DiagnosticDNS Name Lookup PingFirmware Upgrade Factory DefaultSystem Management Restart Firmware DownloadImport Configuration File Port Management Port SetupExport Configuration File Basic Per Port ConfigFirewall General Port Management Port StatusPort Status GeneralRestrict WEB Features Firewall Access RulesServices Access RulesAdd a New Access Rule Scheduling Firewall Content FilterProtectLink Content FilterVPN Summary SummaryClient to Gateway GroupVPN StatusGateway to Gateway VPN Gateway to Gateway Local Group SetupAdd a New Tunnel VPN Clients StatusLocal Security Group Type Remote Security Gateway Type Remote Group SetupRemote Security Group Type IPSec SetupIKE with Preshared Key Keying Mode Manual Advanced VPN Client to GatewayTunnel No The tunnel number is automatically generated TunnelRemote Client Remote Client SetupGroup VPN Default is Domain NameFQDN Keying Mode Manual Tunnel Only VPN VPN Client Access VPN VPN Pass Through VPN Client AccessVPN Client Users Certificate ManagementLog System Log VPN Pptp ServerVPN Pass Through Pptp ServerSystem Log Log SettingSyslog MailLog System Statistics Wizard Basic SetupObtain an IP automatically Minutes PPPoEAccess Rule Setup Select the Log Rule Logout SupportManual Linksys Web SiteAppendix a Appendix a TroubleshootingTroubleshooting Appendix B Appendix BLinksys QuickVPN for Windows 2000, XP, or VistaInstall from the CD-ROM Linksys QuickVPN Client Installation and ConfigurationClick the VPN Client Access tab Click Add to list Click Save SettingsClick Business Click Router/VPN Solutions Install the Client CertificateDownload from the Internet Linksys QuickVPN ConnectionVersion Number of Linksys QuickVPN Confirm New Password Re-enter your new passwordAppendix C Configuration of the RVL200Appendix C Gateway-to-Gateway VPN Tunnel Before You BeginConfiguration of PC 1 and PC Configuration of the RV042RV042 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix C Configuration of Router a Configuration of ScenarioAppendix D Appendix D IPSec NAT TraversalIPSec NAT Traversal Configuration of Router BClick the One-to-One NAT tab One-to-One NAT Rule on NAT 2 RV042One-to-One NAT Rule on NAT 1 RV042 Configuration of Router a Appendix D Appendix E Creation of New ServicesAppendix E Bandwidth Management Bandwidth ManagementCreation of New Bandwidth Management Rules Firmware Upgrade Appendix F Firmware UpgradeUpgrade the Firmware Alternative Firmware Upgrade OptionFirmware Upgrade How to Purchase, Register, or Activate the Service Appendix G Trend Micro ProtectLink Gateway ServiceAppendix G System SummaryProtectLink How to Use the ServiceWeb Protection ProtectLink Web ProtectionProtectLink License ProtectLink Email ProtectionEmail Protection LicenseAppendix G Appendix H Appendix H SpecificationsSpecifications Obtaining Warranty Service Warranty InformationAppendix Exclusions and LimitationsTechnical Support Warranty InformationAppendix J Software License Agreement Appendix JSoftware in Linksys Products Software LicensesSoftware License Agreement SchedulePreamble Appendix J END of Terms and Conditions Original SSLeay License OpenSSL LicenseAppendix J Regulatory Information Appendix KDansk Danish Miljøinformation for kunder i EU Appendix K Norsk Norwegian Miljøinformasjon for kunder i EU Appendix K Contact Information Appendix L
Top Page Image Contents