Cisco Systems RV042RF manual Appendix K, Regulatory Information

Page 98

Appendix K

Appendix K: Regulatory Information

FCC Statement

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•• Reorient or relocate the receiving antenna

•• Increase the separation between the equipment or devices

•• Connect the equipment to an outlet other than the receiver’s

•• Consult a dealer or an experienced radio/TV technician for assistance

Safety Notices

•• Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.

•• Do not use this product near water, for example, in a wet basement or near a swimming pool.

•• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Regulatory Information

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Operation is subject to the following two conditions:

1.This device may not cause interference and

2.This device must accept any interference, including interference that may cause undesired operation of the device.

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Le fonctionnement est soumis aux conditions suivantes :

1.Ce périphérique ne doit pas causer d’interférences;

2.Ce périphérique doit accepter toutes les interférences reçues, y compris celles qui risquent d’entraîner un fonctionnement indésirable.

10/100 4-Port VPN Router

91

Image 98
Contents 10/100 4-Port VPN Router Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Ddns Appendix a Troubleshooting Appendix B Linksys QuickVPN for Windows 2000, XP, or VistaAppendix G Trend Micro ProtectLink Gateway Service Appendix F Firmware UpgradeAppendix H Specifications Appendix D IPSec NAT TraversalAppendix L Contact Information Appendix I Warranty InformationAppendix K Regulatory Information Introduction ChapterChapter Introduction Computer using VPN client software to VPN Router Chapter Product Overview Product OverviewPhysical Installation Chapter InstallationInstallation Cable ConnectionsInstallation How to Access the Web-Based Utility Chapter Advanced ConfigurationAdvanced Configuration OverviewPort Statistics ConfigurationSystem Information Trend Micro ProtectLink GatewayVPN Setting Status Network Setting StatusFirewall Setting Status Log Setting StatusNetwork Setup Tab NetworkLAN Setting Dual-WAN/DMZ Setting WAN Connection TypePPPoE Point-to-Point Protocol over Ethernet Pptp Point-to-Point Tunneling ProtocolSetup Password Heart Beat SignalPassword Setup TimeSetup DMZ Host TimePort Range Forwarding Setup Tab ForwardingForwarding Port TriggeringSetup UPnP UPnPOne-to-One NAT Setup One-to-One NATSetup MAC Clone Add RangeWAN1/2 Setup DdnsMAC Clone DynDNS.orgDynamic Routing Setup Advanced RoutingAdvanced Routing Oray.net PeanutHull DdnsDhcp Setup Static RoutingStatic IP SetupDynamic IP Status Smart Link BackupDhcp Status Dual-WANNetwork Service Detection Load BalanceProtocol Binding System Management Bandwidth ManagementBandwidth WAN1/2 Bandwidth Management Type Bandwidth ManagementMaximum Bandwidth provided by ISP Rate ControlSystem Management Snmp PriorityDNS Name Lookup System Management DiagnosticDiagnostic PingSystem Management Restart Factory DefaultFirmware Upgrade Firmware DownloadExport Configuration File Port Management Port SetupImport Configuration File Basic Per Port ConfigPort Status Port Management Port StatusFirewall General GeneralFirewall Access Rules Restrict WEB FeaturesServices Access RulesAdd a New Access Rule Firewall Content Filter SchedulingVPN Summary Content FilterProtectLink SummaryClient to Gateway GroupVPN StatusGateway to Gateway Add a New Tunnel Local Group SetupVPN Gateway to Gateway VPN Clients StatusLocal Security Group Type Remote Group Setup Remote Security Gateway TypeRemote Security Group Type IPSec SetupIKE with Preshared Key Keying Mode Manual VPN Client to Gateway AdvancedTunnel Tunnel No The tunnel number is automatically generatedRemote Client Setup Remote ClientGroup VPN Default is Domain NameFQDN Keying Mode Manual Tunnel Only VPN VPN Client Access VPN Client Users VPN Client AccessVPN VPN Pass Through Certificate ManagementVPN Pass Through VPN Pptp ServerLog System Log Pptp ServerSyslog Log SettingSystem Log MailLog System Statistics Basic Setup WizardObtain an IP automatically PPPoE MinutesAccess Rule Setup Select the Log Rule Manual SupportLogout Linksys Web SiteAppendix a Appendix a TroubleshootingTroubleshooting Linksys QuickVPN for Appendix BAppendix B Windows 2000, XP, or VistaClick the VPN Client Access tab Linksys QuickVPN Client Installation and ConfigurationInstall from the CD-ROM Click Add to list Click Save SettingsDownload from the Internet Install the Client CertificateClick Business Click Router/VPN Solutions Linksys QuickVPN ConnectionConfirm New Password Re-enter your new password Version Number of Linksys QuickVPNAppendix C Gateway-to-Gateway VPN Tunnel Configuration of the RVL200Appendix C Before You BeginConfiguration of the RV042 Configuration of PC 1 and PCRV042 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix C Appendix D Configuration of ScenarioConfiguration of Router a Appendix D IPSec NAT TraversalConfiguration of Router B IPSec NAT TraversalClick the One-to-One NAT tab One-to-One NAT Rule on NAT 2 RV042One-to-One NAT Rule on NAT 1 RV042 Configuration of Router a Appendix D Appendix E Bandwidth Management Creation of New ServicesAppendix E Bandwidth ManagementCreation of New Bandwidth Management Rules Upgrade the Firmware Appendix F Firmware UpgradeFirmware Upgrade Alternative Firmware Upgrade OptionFirmware Upgrade Appendix G Appendix G Trend Micro ProtectLink Gateway ServiceHow to Purchase, Register, or Activate the Service System SummaryHow to Use the Service ProtectLinkProtectLink Web Protection Web ProtectionEmail Protection ProtectLink Email ProtectionProtectLink License LicenseAppendix G Appendix H Appendix H SpecificationsSpecifications Appendix Warranty InformationObtaining Warranty Service Exclusions and LimitationsWarranty Information Technical SupportSoftware in Linksys Products Appendix JAppendix J Software License Agreement Software LicensesSchedule Software License AgreementPreamble Appendix J END of Terms and Conditions OpenSSL License Original SSLeay LicenseAppendix J Appendix K Regulatory InformationDansk Danish Miljøinformation for kunder i EU Appendix K Norsk Norwegian Miljøinformasjon for kunder i EU Appendix K Appendix L Contact Information