Cisco Systems RV042RF manual Tunnel No The tunnel number is automatically generated

Page 48

Chapter 4

Advanced Configuration

VPN > Client to Gateway

NOTE: The 10/100 4-Port VPN Router supports IPSec VPN client software, including the Linksys QuickVPN software.

To manage access for Linksys QuickVPN clients, click the VPN Client Access tab. (For more information about QuickVPN, refer to “Appendix B: Linksys QuickVPN for Windows 2000, XP, or Vista”.)

Add a New Tunnel

Tunnel/Group VPN  To create a tunnel for a single VPN client, select Tunnel. To create a tunnel for multiple VPN clients, select GroupVPN.The GroupVPN feature facilitates setup and is not needed to individually configure remote VPN clients.

Depending on your selection, the Local Group Setup and Remote Client Setup settings will differ. Proceed to the appropriate instructions for your selection.

Tunnel

Tunnel No  The tunnel number is automatically generated.

Tunnel Name  Enter a name for this VPN tunnel, such as Los Angeles Office, Chicago Branch, or New York Division.

This allows you to identify multiple tunnels and does not have to match the name used at the other end of the tunnel.

Interface  Select the appropriate WAN port, WAN1 or WAN2 (available if the Dual WAN feature is enabled).

Enable  Check this box to enable a VPN tunnel.

Local Group Setup

Local Security Gateway Type

Select the type you want to use: IP Only, IP + Domain Name(FQDN) Authentication, IP + E-mail Addr.(USER FQDN) Authentication, Dynamic IP + Domain Name(FQDN) Authentication, or Dynamic IP + E- mail Addr.(USER FQDN) Authentication. Follow the instructions for the type you want to use.

NOTE: The Local Security Gateway Type you select should match the Remote Security Gateway Type selected on the VPN device at the other end of the tunnel.

IP Only

The default is IP Only. Only the device with a specific IP address will be able to access the tunnel.

Local Security Gateway Type > IP Only

IP address  The WAN (or Internet) IP address of the Router automatically appears.

IP + Domain Name(FQDN) Authentication

The IP address and FQDN must match the Remote Security Gateway of the remote VPN device, and they can only be used for one tunnel connection.

Local Security Gateway Type > IP + Domain Name(FQDN)

Authentication

Domain Name  Enter the Fully Qualified Domain Name (FQDN), which is the host name and domain name for a specific computer on the Internet.

IP address  The WAN (or Internet) IP address of the Router automatically appears.

10/100 4-Port VPN Router

41

Page 47 Page 49
Image 48
Page 47 Page 49
Contents 10/100 4-Port VPN Router About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Ddns Appendix a Troubleshooting Appendix B Linksys QuickVPN for Windows 2000, XP, or VistaAppendix F Firmware Upgrade Appendix H SpecificationsAppendix G Trend Micro ProtectLink Gateway Service Appendix D IPSec NAT TraversalAppendix I Warranty Information Appendix K Regulatory InformationAppendix L Contact Information Chapter Chapter IntroductionIntroduction Computer using VPN client software to VPN Router Chapter Product Overview Product OverviewChapter Installation InstallationPhysical Installation Cable ConnectionsInstallation Chapter Advanced Configuration Advanced ConfigurationHow to Access the Web-Based Utility OverviewConfiguration System InformationPort Statistics Trend Micro ProtectLink GatewayNetwork Setting Status Firewall Setting StatusVPN Setting Status Log Setting StatusSetup Tab Network LAN SettingNetwork Dual-WAN/DMZ Setting WAN Connection TypePPPoE Point-to-Point Protocol over Ethernet Pptp Point-to-Point Tunneling ProtocolSetup Password Heart Beat SignalSetup Time Setup DMZ HostPassword TimeSetup Tab Forwarding ForwardingPort Range Forwarding Port TriggeringSetup UPnP UPnPSetup One-to-One NAT Setup MAC CloneOne-to-One NAT Add RangeSetup Ddns MAC CloneWAN1/2 DynDNS.orgSetup Advanced Routing Advanced RoutingDynamic Routing Oray.net PeanutHull DdnsDhcp Setup Static RoutingSetup Dynamic IPStatic IP Smart Link Backup Dhcp StatusStatus Dual-WANNetwork Service Detection Load BalanceSystem Management Bandwidth Management Bandwidth WAN1/2Protocol Binding Bandwidth Management Maximum Bandwidth provided by ISPBandwidth Management Type Rate ControlSystem Management Snmp PrioritySystem Management Diagnostic DiagnosticDNS Name Lookup PingFactory Default Firmware UpgradeSystem Management Restart Firmware DownloadPort Management Port Setup Import Configuration FileExport Configuration File Basic Per Port ConfigPort Management Port Status Firewall GeneralPort Status GeneralFirewall Access Rules Restrict WEB FeaturesAccess Rules Add a New Access RuleServices Firewall Content Filter SchedulingContent Filter ProtectLinkVPN Summary SummaryGroupVPN Status Gateway to GatewayClient to Gateway Local Group Setup VPN Gateway to GatewayAdd a New Tunnel VPN Clients StatusLocal Security Group Type Remote Group Setup Remote Security Gateway TypeIPSec Setup IKE with Preshared KeyRemote Security Group Type Keying Mode Manual VPN Client to Gateway AdvancedTunnel Tunnel No The tunnel number is automatically generatedRemote Client Setup Remote ClientGroup VPN Default is Domain NameFQDN Keying Mode Manual Tunnel Only VPN VPN Client Access VPN Client Access VPN VPN Pass ThroughVPN Client Users Certificate ManagementVPN Pptp Server Log System LogVPN Pass Through Pptp ServerLog Setting System LogSyslog MailLog System Statistics Basic Setup WizardObtain an IP automatically PPPoE MinutesAccess Rule Setup Select the Log Rule Support LogoutManual Linksys Web SiteAppendix a Troubleshooting TroubleshootingAppendix a Appendix B Appendix BLinksys QuickVPN for Windows 2000, XP, or VistaLinksys QuickVPN Client Installation and Configuration Install from the CD-ROMClick the VPN Client Access tab Click Add to list Click Save SettingsInstall the Client Certificate Click Business Click Router/VPN SolutionsDownload from the Internet Linksys QuickVPN ConnectionConfirm New Password Re-enter your new password Version Number of Linksys QuickVPNConfiguration of the RVL200 Appendix CAppendix C Gateway-to-Gateway VPN Tunnel Before You BeginConfiguration of the RV042 Configuration of PC 1 and PCRV042 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix C Configuration of Scenario Configuration of Router aAppendix D Appendix D IPSec NAT TraversalConfiguration of Router B IPSec NAT TraversalOne-to-One NAT Rule on NAT 2 RV042 One-to-One NAT Rule on NAT 1 RV042Click the One-to-One NAT tab Configuration of Router a Appendix D Creation of New Services Appendix EAppendix E Bandwidth Management Bandwidth ManagementCreation of New Bandwidth Management Rules Appendix F Firmware Upgrade Firmware UpgradeUpgrade the Firmware Alternative Firmware Upgrade OptionFirmware Upgrade Appendix G Trend Micro ProtectLink Gateway Service How to Purchase, Register, or Activate the ServiceAppendix G System SummaryHow to Use the Service ProtectLinkProtectLink Web Protection Web ProtectionProtectLink Email Protection ProtectLink LicenseEmail Protection LicenseAppendix G Appendix H Specifications SpecificationsAppendix H Warranty Information Obtaining Warranty ServiceAppendix Exclusions and LimitationsWarranty Information Technical SupportAppendix J Appendix J Software License AgreementSoftware in Linksys Products Software LicensesSchedule Software License AgreementPreamble Appendix J END of Terms and Conditions OpenSSL License Original SSLeay LicenseAppendix J Appendix K Regulatory InformationDansk Danish Miljøinformation for kunder i EU Appendix K Norsk Norwegian Miljøinformasjon for kunder i EU Appendix K Appendix L Contact Information
Top Page Image Contents