Cisco Systems RV042RF manual System Management Restart, Factory Default, Firmware Upgrade

Page 34

Chapter 4

Advanced Configuration

System Management > Diagnostic > Ping

Ping host or IP address Enter the IP address of the device being pinged, and click Go. The test will take a few seconds to complete. Then the Router will display the results.

Status The status of the ping test is displayed.

Packets The number of packets transmitted, number of packets received, and percentage of packets lost are displayed.

Round Trip Time The minimum, maximum, and average round trip times are displayed.

System Management > Factory Default

Use this screen to clear all of your configuration information and restore the Router to its factory default settings. Only use this feature if you wish to discard all the settings and preferences that you have configured.

System Management > Factory Default

Factory Default

Return to Factory Default Setting Click Return to Factory Default Setting if you want to restore the Router to its factory default settings. After clicking the button, a confirmation screen appears. Click OK to continue.

Factory Default Confirmation

System Management > Firmware Upgrade

You can use this feature to upgrade the Router’s firmware to the latest version.

System Management > Firmware Upgrade

Firmware Upgrade

To download the firmware, refer to the Firmware Download instructions. If you have already downloaded the firmware onto your computer, then click the Browse button to look for the extracted file.

Firmware Upgrade Right Now After you have selected the extracted file, click Firmware Upgrade Right Now.

NOTE: The Router will take approximately ten minutes to upgrade its firmware. During this process, do not power off the Router or press the Reset button.

Firmware Download

Firmware Download from Linksys Web Site If you need to download the latest version of the Router’s firmware, click Firmware Download from Linksys Web Site. The Support page of the Linksys website appears.

Follow the on-screen instructions to access the Downloads page for the 10/100 4-Port VPN Router (model number: RV042). Then download the firmware upgrade file.

Extract the file on your computer.Then follow the Firmware Upgrade instructions.

System Management > Restart

If you need to restart the Router, Linksys recommends that you use the Restart tool on this screen. When you restart

10/100 4-Port VPN Router

27

Image 34

Contents 10/100 4-Port VPN Router Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Ddns Appendix a Troubleshooting Appendix B Linksys QuickVPN for Windows 2000, XP, or VistaAppendix G Trend Micro ProtectLink Gateway Service Appendix F Firmware UpgradeAppendix H Specifications Appendix D IPSec NAT TraversalAppendix K Regulatory Information Appendix I Warranty InformationAppendix L Contact Information Chapter Introduction ChapterIntroduction Computer using VPN client software to VPN Router Chapter Product Overview Product OverviewPhysical Installation Chapter InstallationInstallation Cable ConnectionsInstallation How to Access the Web-Based Utility Chapter Advanced ConfigurationAdvanced Configuration OverviewPort Statistics ConfigurationSystem Information Trend Micro ProtectLink GatewayVPN Setting Status Network Setting StatusFirewall Setting Status Log Setting StatusLAN Setting Setup Tab NetworkNetwork Dual-WAN/DMZ Setting WAN Connection TypePPPoE Point-to-Point Protocol over Ethernet Pptp Point-to-Point Tunneling ProtocolSetup Password Heart Beat SignalPassword Setup TimeSetup DMZ Host TimePort Range Forwarding Setup Tab ForwardingForwarding Port TriggeringSetup UPnP UPnPOne-to-One NAT Setup One-to-One NATSetup MAC Clone Add RangeWAN1/2 Setup DdnsMAC Clone DynDNS.orgDynamic Routing Setup Advanced RoutingAdvanced Routing Oray.net PeanutHull DdnsDhcp Setup Static RoutingDynamic IP SetupStatic IP Status Smart Link BackupDhcp Status Dual-WANNetwork Service Detection Load BalanceBandwidth WAN1/2 System Management Bandwidth ManagementProtocol Binding Bandwidth Management Type Bandwidth ManagementMaximum Bandwidth provided by ISP Rate ControlSystem Management Snmp PriorityDNS Name Lookup System Management DiagnosticDiagnostic PingSystem Management Restart Factory DefaultFirmware Upgrade Firmware DownloadExport Configuration File Port Management Port SetupImport Configuration File Basic Per Port ConfigPort Status Port Management Port StatusFirewall General GeneralFirewall Access Rules Restrict WEB FeaturesAdd a New Access Rule Access RulesServices Firewall Content Filter SchedulingVPN Summary Content FilterProtectLink SummaryGateway to Gateway GroupVPN StatusClient to Gateway Add a New Tunnel Local Group SetupVPN Gateway to Gateway VPN Clients StatusLocal Security Group Type Remote Group Setup Remote Security Gateway TypeIKE with Preshared Key IPSec SetupRemote Security Group Type Keying Mode Manual VPN Client to Gateway AdvancedTunnel Tunnel No The tunnel number is automatically generatedRemote Client Setup Remote ClientGroup VPN Default is Domain NameFQDN Keying Mode Manual Tunnel Only VPN VPN Client Access VPN Client Users VPN Client AccessVPN VPN Pass Through Certificate ManagementVPN Pass Through VPN Pptp ServerLog System Log Pptp ServerSyslog Log SettingSystem Log MailLog System Statistics Basic Setup WizardObtain an IP automatically PPPoE MinutesAccess Rule Setup Select the Log Rule Manual SupportLogout Linksys Web SiteTroubleshooting Appendix a TroubleshootingAppendix a Linksys QuickVPN for Appendix BAppendix B Windows 2000, XP, or VistaClick the VPN Client Access tab Linksys QuickVPN Client Installation and ConfigurationInstall from the CD-ROM Click Add to list Click Save SettingsDownload from the Internet Install the Client CertificateClick Business Click Router/VPN Solutions Linksys QuickVPN ConnectionConfirm New Password Re-enter your new password Version Number of Linksys QuickVPNAppendix C Gateway-to-Gateway VPN Tunnel Configuration of the RVL200Appendix C Before You BeginConfiguration of the RV042 Configuration of PC 1 and PCRV042 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix C Appendix D Configuration of ScenarioConfiguration of Router a Appendix D IPSec NAT TraversalConfiguration of Router B IPSec NAT TraversalOne-to-One NAT Rule on NAT 1 RV042 One-to-One NAT Rule on NAT 2 RV042Click the One-to-One NAT tab Configuration of Router a Appendix D Appendix E Bandwidth Management Creation of New ServicesAppendix E Bandwidth ManagementCreation of New Bandwidth Management Rules Upgrade the Firmware Appendix F Firmware UpgradeFirmware Upgrade Alternative Firmware Upgrade OptionFirmware Upgrade Appendix G Appendix G Trend Micro ProtectLink Gateway ServiceHow to Purchase, Register, or Activate the Service System SummaryHow to Use the Service ProtectLinkProtectLink Web Protection Web ProtectionEmail Protection ProtectLink Email ProtectionProtectLink License LicenseAppendix G Specifications Appendix H SpecificationsAppendix H Appendix Warranty InformationObtaining Warranty Service Exclusions and LimitationsWarranty Information Technical SupportSoftware in Linksys Products Appendix JAppendix J Software License Agreement Software LicensesSchedule Software License AgreementPreamble Appendix J END of Terms and Conditions OpenSSL License Original SSLeay LicenseAppendix J Appendix K Regulatory InformationDansk Danish Miljøinformation for kunder i EU Appendix K Norsk Norwegian Miljøinformasjon for kunder i EU Appendix K Appendix L Contact Information