Cisco Systems RV042RF manual Remote Group Setup, Remote Security Gateway Type

Page 44

Chapter 4

Advanced Configuration

Local Security Group Type > IP Range

IP range  Enter the range of IP addresses. The default is 192.168.1.0~254.

Remote Group Setup

Before you configure the Remote Group Setup, make sure your VPN tunnel will have two different IP subnets. For example, if the local VPN Router has an IP scheme of 192.168.1.x (x being a number from 1 to 254), then the remote VPN router should have a different IP scheme, such as 192.168.2.y (y being a number from 1 to 254). Otherwise, the IP addresses will conflict, and the VPN tunnel cannot be created.

Remote Security Gateway Type

Select the type you want to use: IP Only, IP + Domain Name(FQDN) Authentication, IP + E-mail Addr.(USER FQDN) Authentication, Dynamic IP + Domain Name(FQDN) Authentication, or Dynamic IP + E- mail Addr.(USER FQDN) Authentication. Follow the instructions for the type you want to use.

NOTE: The Remote Security Gateway Type you select should match the Local Security Gateway Type selected on the VPN device at the other end of the tunnel.

IP Only

The default is IP Only. Only the device with a specific IP address will be able to access the tunnel. Select IP address or IP by DNS Resolved.

Remote Security Gateway Type > IP Only

IP address  Select this option if you know the static IP address of the remote VPN device at the other end of the tunnel, and then enter the IP address.

IP by DNS Resolved  Select this option if you do not know the static IP address of the remote VPN device but you do know its domain name. Then enter the remote VPN device’s domain name on the Internet. The Router will retrieve the IP address of the remote VPN device via its public DNS records.

IP + Domain Name(FQDN) Authentication

The IP address and domain name ID must match the Local Gateway of the remote VPN device, and they can only be used for one tunnel connection.

Remote Security Gateway Type > IP + Domain Name(FQDN)

Authentication

IP address  Select this option if you know the static IP address of the remote VPN device at the other end of the tunnel, and then enter the IP address.

IP by DNS Resolved  Select this option if you do not know the static IP address of the remote VPN device but you do know its domain name. Then enter the remote VPN device’s domain name on the Internet. The Router will retrieve the IP address of the remote VPN device via its public DNS records.

Domain Name  Enter the domain name as an ID (it cannot be a real domain name on the Internet).

IP + E-mail Addr.(USER FQDN) Authentication

Remote Security Gateway Type > IP + E-mail Addr.(USER FQDN)

Authentication

IP address  Select this option if you know the static IP address of the remote VPN device at the other end of the tunnel, and then enter the IP address.

IP by DNS Resolved  Select this option if you do not know the static IP address of the remote VPN device but you do know its domain name. Then enter the remote VPN device’s domain name on the Internet. The Router will retrieve the IP address of the remote VPN device via its public DNS records.

E-mail address  Enter the e-mail address as an ID. Dynamic IP + Domain Name(FQDN) Authentication

The Local Security Gateway will be a dynamic IP address, so you do not need to enter the IP address. When the Remote Security Gateway requests to create a tunnel with the Router, the Router will work as a responder.

The domain name must match the Local Gateway of the remote VPN device and can only be used for one tunnel connection.

10/100 4-Port VPN Router

37

Page 43 Page 45
Image 44
Page 43 Page 45
Contents 10/100 4-Port VPN Router About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Ddns Appendix a Troubleshooting Appendix B Linksys QuickVPN for Windows 2000, XP, or VistaAppendix F Firmware Upgrade Appendix H SpecificationsAppendix G Trend Micro ProtectLink Gateway Service Appendix D IPSec NAT TraversalAppendix L Contact Information Appendix I Warranty InformationAppendix K Regulatory Information Introduction ChapterChapter Introduction Computer using VPN client software to VPN Router Chapter Product Overview Product OverviewChapter Installation InstallationPhysical Installation Cable ConnectionsInstallation Chapter Advanced Configuration Advanced ConfigurationHow to Access the Web-Based Utility OverviewConfiguration System InformationPort Statistics Trend Micro ProtectLink GatewayNetwork Setting Status Firewall Setting StatusVPN Setting Status Log Setting StatusNetwork Setup Tab NetworkLAN Setting Dual-WAN/DMZ Setting WAN Connection TypePPPoE Point-to-Point Protocol over Ethernet Pptp Point-to-Point Tunneling ProtocolSetup Password Heart Beat SignalSetup Time Setup DMZ HostPassword TimeSetup Tab Forwarding ForwardingPort Range Forwarding Port TriggeringSetup UPnP UPnPSetup One-to-One NAT Setup MAC CloneOne-to-One NAT Add RangeSetup Ddns MAC CloneWAN1/2 DynDNS.orgSetup Advanced Routing Advanced RoutingDynamic Routing Oray.net PeanutHull DdnsDhcp Setup Static RoutingStatic IP SetupDynamic IP Smart Link Backup Dhcp StatusStatus Dual-WANNetwork Service Detection Load BalanceProtocol Binding System Management Bandwidth ManagementBandwidth WAN1/2 Bandwidth Management Maximum Bandwidth provided by ISPBandwidth Management Type Rate ControlSystem Management Snmp PrioritySystem Management Diagnostic DiagnosticDNS Name Lookup PingFactory Default Firmware UpgradeSystem Management Restart Firmware DownloadPort Management Port Setup Import Configuration FileExport Configuration File Basic Per Port ConfigPort Management Port Status Firewall GeneralPort Status GeneralFirewall Access Rules Restrict WEB FeaturesServices Access RulesAdd a New Access Rule Firewall Content Filter SchedulingContent Filter ProtectLinkVPN Summary SummaryClient to Gateway GroupVPN StatusGateway to Gateway Local Group Setup VPN Gateway to GatewayAdd a New Tunnel VPN Clients StatusLocal Security Group Type Remote Group Setup Remote Security Gateway TypeRemote Security Group Type IPSec SetupIKE with Preshared Key Keying Mode Manual VPN Client to Gateway AdvancedTunnel Tunnel No The tunnel number is automatically generatedRemote Client Setup Remote ClientGroup VPN Default is Domain NameFQDN Keying Mode Manual Tunnel Only VPN VPN Client Access VPN Client Access VPN VPN Pass ThroughVPN Client Users Certificate ManagementVPN Pptp Server Log System LogVPN Pass Through Pptp ServerLog Setting System LogSyslog MailLog System Statistics Basic Setup WizardObtain an IP automatically PPPoE MinutesAccess Rule Setup Select the Log Rule Support LogoutManual Linksys Web SiteAppendix a Appendix a TroubleshootingTroubleshooting Appendix B Appendix BLinksys QuickVPN for Windows 2000, XP, or VistaLinksys QuickVPN Client Installation and Configuration Install from the CD-ROMClick the VPN Client Access tab Click Add to list Click Save SettingsInstall the Client Certificate Click Business Click Router/VPN SolutionsDownload from the Internet Linksys QuickVPN ConnectionConfirm New Password Re-enter your new password Version Number of Linksys QuickVPNConfiguration of the RVL200 Appendix CAppendix C Gateway-to-Gateway VPN Tunnel Before You BeginConfiguration of the RV042 Configuration of PC 1 and PCRV042 RVL200 Dynamic IP B.B.B.B with Configuration when Both Gateways Use Dynamic IP Addresses Appendix C Configuration of Scenario Configuration of Router aAppendix D Appendix D IPSec NAT TraversalConfiguration of Router B IPSec NAT TraversalClick the One-to-One NAT tab One-to-One NAT Rule on NAT 2 RV042One-to-One NAT Rule on NAT 1 RV042 Configuration of Router a Appendix D Creation of New Services Appendix EAppendix E Bandwidth Management Bandwidth ManagementCreation of New Bandwidth Management Rules Appendix F Firmware Upgrade Firmware UpgradeUpgrade the Firmware Alternative Firmware Upgrade OptionFirmware Upgrade Appendix G Trend Micro ProtectLink Gateway Service How to Purchase, Register, or Activate the ServiceAppendix G System SummaryHow to Use the Service ProtectLinkProtectLink Web Protection Web ProtectionProtectLink Email Protection ProtectLink LicenseEmail Protection LicenseAppendix G Appendix H Appendix H SpecificationsSpecifications Warranty Information Obtaining Warranty ServiceAppendix Exclusions and LimitationsWarranty Information Technical SupportAppendix J Appendix J Software License AgreementSoftware in Linksys Products Software LicensesSchedule Software License AgreementPreamble Appendix J END of Terms and Conditions OpenSSL License Original SSLeay LicenseAppendix J Appendix K Regulatory InformationDansk Danish Miljøinformation for kunder i EU Appendix K Norsk Norwegian Miljøinformasjon for kunder i EU Appendix K Appendix L Contact Information
Top Page Image Contents