Grizzly G0512 instruction manual Machine Data Sheet

Page 34

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

GRIZZLY MODEL G0512 HEAVY-DUTY EDGE SANDER

Design Type	Expanded Table, Floor Model
Overall Dimensions and Specifications:
Table Size	24" x 421⁄4"
Overall Height (With Handle Up)	483⁄4"
Table Height	33"-39"
Length	521⁄2"
Width	24"
Platen Size	61⁄4'' x 311⁄2", Graphite Coated
Belt Size	6" x 80"
Belt Speed	1800 FPM
Shipping Weight	250 lbs.
Machine Weight	235 lbs.
Footprint	141⁄2" x 32"
Construction:
Base	Welded Steel - Powder Coated
Table	Composite w/ Formica Surface
Rubber Idler Roller	Shielded Ball Bearing, 21⁄8"
Drive Roller	Cast Aluminum, 41⁄2"
Motor:
Type	TEFC Capacitor Start Induction
Horsepower	11⁄2 HP
Phase / Voltage	Single Phase ⁄ 110V ⁄ 220V; Prewired 220V
Amps	20 ⁄ 10
Cycle and RPM	60 Hertz ⁄ 1725 RPM
Switch	Toggle Safety Switch w/ Safety Lock Tab
Power Transfer	Direct Drive
Bearings	Shielded & Lubricated Ball Bearings
Features:
............................................................................................	Extended Sanding Surface
......................................................................................................................	Work Stop
....................................................................................................................	4" Dust Port
........................................................................................................	Quick Belt Release
..........................................................................	Belt Tracking and Tension Adjustment
............................................................................	Handwheel Table Height Adjustment
....................................................................................................	Powder Coated Stand

Specifications, while deemed accurate, are not guaranteed.

-32-	G0512 Edge Sander

Image 34

Contents Edge Sander Page Table of Contents Safety Safety Instructions For Power ToolsLength Additional Safety Instructions For Sanders Introduction Plug Type Circuit RequirementsAmperage Draw Circuit Breaker RequirementsGrounding Extension Cords 110V OperationIdentification Unpacking SET UPG0512 Inventory Hardware Recognition Chart Floor Load Clean UpSite Considerations Working ClearancesInstalling Feet Beginning AssemblyTo install the feet on the sander To install the tension lever Installing Tension LeverInstalling Sanding Belt To install the sanding beltAttaching Dust Port Connecting Plug to CordInstall the plug and receptacle now To attach the dust portTo install the roller guard Installing Roller GuardTest Run & Tracking Installing Table To test run and track the beltAllen wrench placed between platen To install the back stop Installing Back StopConnecting to Dust Collection System To connect the dust port to a dust collection systemPower Switch OperationsHeight To adjust the tableSanding Belt Model G0512 accepts a 6 x 80 sanding beltEdge & End Sanding Typical edge sanding operationContour Sanding Lubrication MaintenanceGeneral BearingsAbout Service Service AdjustmentsAdjusting Tensioner Resetting Tensioner Spring Tension Tensioner spring Tracking control boltParallel Belt Tracking To check the parallel tracking of the sanding beltIdler roller adjustment screws G0512 Edge Sander Platen-to-Rollers Adjustments To check the platen-to-idler roller relation- shipRemove the sanding belt G0512 Edge Sander Remove the sanding belt and dust port Reference Info Aftermarket AccessoriesPRO-STICKAbrasive Belt Cleaners Extra 6 x 80 Belts Grit ModelMachine Data Sheet Breakdown and List Description Troubleshooting Machine Symptom Possible Cause Corrective ActionTroubleshooting Sanding G0512 Wiring Diagram Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage #ALL 4ODAYD&ORO