Craftsman 113.225900, 113.225931, 113.225909 manual Belt Adjusting Screw ONE on Each Side

Page 17

1. ABRASIVE BELT ADJUSTING SCREWS

cause the idler pulley to move in or out for applying tension to the abrasive belt or for tracking it. They are adjusted using the 1/2" wrenches,

See "Assembly" section... "Installing Abrasive Belt".

2. ABRASIVE BELT LOCKING SCREWS lock the adjustment mechanism after the abrasive belt is tensioned and tracking properly, They are locked using the 1/2" wrench.

See "assembly" section . . . "Installing Abrasive Belt".

3, WORK TABLE TILT LOCK SCREW locks

the table. It is locked using the 1/2" wrencn.

a. Using a combination square, check the angle of the table with the disc.

NOTE: The :ombination square must be "true"--

See start of assembly section on Pg. 6 for checking method.

b. If the table Js not 90 ° with the disc.., loosen tilt Ic_ck screw and ti t table,

c. Loosen the lock nut using a 7/16" wrench.

d. Screw the atop screw in or out. using a 3/8"" wrench so that when the table touches the stop screw, the table is 90 ° to the disc.

e. Tighten the lock nut

BELT ADJUSTING

SCREW

(ONE ON EACH SIDE)

BELT LOCKING

SCREW

(ONE ON EACH SIDE)

 

 

\

 

 

/

TABLE

1/2"

 

FROM

DISC

TABLE

POSITIONING

 

 

LOCK

SCREW

 

 

STOP

SCREW

_" TILT

LOCK NUT

LOCK

SCREW

17

Image 17
Contents Legs and Motor Belt and DiscPower tools General safety instructionsSander Before Using the SanderBefore Each USE At a time Whenever Sander is RunningPlan your work Grounded /n Ul OUTLETs Connecting to Power Source OutletProperly Unpacking and checking ContentsFollowing parts are included with Model AssernbJyHAROWABEFORMOUNTINGTOOL& Motor Catalog no Mounting Belt and Disc Sander on Craftsman Steel LEG SETAssembly Installing Sanding Disc and Dust TrapWrench Belt Table LockingFlat Spot AssemblyDisc Dust Trap Flat Head Screws TrapTWO Holes TOP Right Hand Screw Dust Trap CoverClips 10-32 X 1/2ON-OFF Switch AssemblyInsert key into switch Place the bolt onto the motor pulley by rotating the pulleyFind plastic cable hanger from among the loose parts Power Cord Motor CordCable Directional ARROW\ Be LT Adjusting SCR EWS Installing Work TablePull Wrenches in this Direction to Apply Tension Belt Locking ScrewBelt Leftmoving To Right Installing Belt Dust TrapBelt Locking Screw Drive PulleyAssembWy Installing BackstopGetting to know your belt and disc sander ANY Aojustm EntsFrom Disc Positioning Lock Screw Stop Tilt Lock NUT Belt Adjusting Screw ONE on Each SideGe ng to know you r belt and disc sander Raise the table and loosen the lock nut using a 7/16 wrenchPlace. It is locked uing the 1/2 wrench Lock NUtBefore Each USE Before Using the SanderBasic operation Before freeing any jammed material Surface Finishing on Abrasive BeltFor finishing long pieces, remove the backstop END Finishing on Abrasive BeltCurved Edges Sears Recommends Following Accessories Motor Maintenance LubricationCausing thebelt to sli CAT. noBox Motor wd! notProtector Open, only TooLOW Voltage Trouble Shooting -- MotorRemedy Hardware for Mounting Tool & Motor Parts ListSupplied With Craftsman Belt and Disc Sander Model no .225900 & 113,225931 47222 Housing, DiscWith Plug Repair partsKey Part Description Outlet Before Proceeding Black Wire to Terminal T1 Green Wire to Green ScrewDoes Not Include Key No, 3. Order Separately If Required Repair partsSwitch Mounting Page BEL T and Disc Sander