Craftsman 113.225931, 113.225909 manual Installing Belt Dust Trap, Belt Leftmoving To Right, Pulley

Page 15

4.Hold the abrasive disc with your left hand tO keep it from turning while pushing the belt in the direction

of the arrow. If the abrasive belt slips over the

pulleys, turn both ADJUSTING screws

simultaneously a small amount to apply a little more tension to the abrasive belt.

5.Adjust the tension so that the abrasive belt does not slip very easily when pushing it, while you are holding the disc.

6.Tighten the locking screws,

7.Plug in the power cord. Turn the switch "ON", and

immediately "OFF", noting if the belt moved to the right or to the left.

If it did not move to the right or left, it is

TRACKING properly.

8. IF THE ABRASIVE BELT MOVES TO THE RIGHT:

a. Loosen the LOCKING SCREWon the RIGHT.

b, Place wrenc, h on the ADJUSTING SCREW on the right.

c.Push abrasive belt so it is moving while pulling the wrench toward you. This will move the abrasive belt to the left. PUSHING the wrench will move the belt to the right.

d.The abrasive belt is tracking properly when it is

centered on the DRIVE pulley.

IMPORTANT:	If you have difficulty	tracking	the
abrasive belt, apply more tension.

9. IF THE ABRASIVE BELT MOVES TOTHE LEFT:

a. Loosen the LOCKING SCREW on the LEFT.

b. Place wrench on the ADJUSTING SCREWon the left.

c.Push abrasive belt so it is moving while pulling the wrench toward you, This wilt move the abrasive belt to the right. PUSHING the wrench will move the abrasive belt to the left.

d.The abrasive belt is tracking properly when it is centered on the DRIVE pulley.

IMPORTANT:	If you have difficulty	tracking the
abrasive belt, apply more tension,

\

BELT LOCKING SCREW

PUSH BELT IN DIRECTION

OF ARROW

BELT

LEFTMOVING

TO RIGHT

RIGHT

BELT

LOCKING

SCREW

DRIVE

	BELT ADJUSTING	PULLEY
	SCREW	PULLEY
	SCREW

INSTALLING BELT DUST TRAP

1. Find one 10 - 32 x 9/16" Pan Head screw and a lock-	©
1. Find one 10 - 32 x 9/16" Pan Head screw and a lock-
washer among the loose parts.

15

Image 15

Contents Legs and Motor Belt and DiscPower tools General safety instructionsBefore Using the Sander Before Each USESander Whenever Sander is Running Plan your workAt a time Connecting to Power Source Outlet ProperlyGrounded /n Ul OUTLETs Unpacking and checking ContentsAssernbJy HAROWABEFORMOUNTINGTOOL& MotorFollowing parts are included with Model Catalog no Mounting Belt and Disc Sander on Craftsman Steel LEG SETBelt Table Locking Installing Sanding Disc and Dust TrapAssembly WrenchTrap AssemblyFlat Spot Disc Dust Trap Flat Head Screws10-32 X 1/2 TOP Right Hand Screw Dust Trap CoverTWO Holes ClipsPlace the bolt onto the motor pulley by rotating the pulley AssemblyON-OFF Switch Insert key into switchPower Cord Motor Cord CableFind plastic cable hanger from among the loose parts Belt Locking Screw Installing Work TableDirectional ARROW\ Be LT Adjusting SCR EWS Pull Wrenches in this Direction to Apply TensionPulley Installing Belt Dust TrapBelt Leftmoving To Right Belt Locking Screw DriveANY Aojustm Ents Installing BackstopAssembWy Getting to know your belt and disc sanderFrom Disc Positioning Lock Screw Stop Tilt Lock NUT Belt Adjusting Screw ONE on Each SideLock NUt Raise the table and loosen the lock nut using a 7/16 wrenchGe ng to know you r belt and disc sander Place. It is locked uing the 1/2 wrenchBefore Using the Sander Basic operationBefore Each USE END Finishing on Abrasive Belt Surface Finishing on Abrasive BeltBefore freeing any jammed material For finishing long pieces, remove the backstopCurved Edges CAT. no Motor Maintenance LubricationSears Recommends Following Accessories Causing thebelt to sliToo Motor wd! notBox Protector Open, onlyTrouble Shooting -- Motor RemedyLOW Voltage Parts List Supplied WithHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 47222 Housing, DiscRepair parts Key Part DescriptionWith Plug Outlet Before Proceeding Black Wire to Terminal T1 Green Wire to Green ScrewRepair parts Switch MountingDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander