Craftsman Complete Guide to Belt Disc Sander Parts and Diagrams

Page 25

repair parts

CRAFTSMAN BELT AND DISC SANDER MODEL NO. 113.2259OO & 113.225931

4 3

			FIGURE
		SUPPLIED	WITH
Key	Part
No.	No.	Description
1	62614	Leg
2	;0314	1- Screw,TrussHd. 1/4-20 x 5/8

3STD541025 t* Nut, Hex1/4-20

4TD551225 1* Lockwasher,1/4 External

	68060	Channel,Support
	68060	Stiffener, Side
	68059	Stiffener, Side
7	62615	Stiffener, End
8	168061	Support,Motor
9	_TD541050 1* Nut, Hex1/2-13
10	803835	1- Foot, Leveling

--68062 1- Bagof LooseParts(Not illustrated)

1 PARTS LIST

MODEL 113.225931 ONLY

Key	Part
No.	No.	Description

HARDWARE FOR MOUNTING TOOL & MOTOR

STD523125 t'Screw, Hex Hd. 5/16-18 x 2-1/2

STD551131 _*Lockwasber, External 5/1B

STD541231 t'Nut, Hex Jam 5/16 x 18

STD551031 1*Washer, 11/32 x 11/16 x t/16

STD532507 1"*Bolt. Carriage5/16-18 x 3/4

tThese items all contained in LooseParts Bag,PartNo. _8062.

*StandardHardwareItem - May be PurchasedLeeelly.

Image 25

Contents Legs and Motor Belt and DiscPower tools General safety instructionsBefore Each USE Before Using the SanderSander Plan your work Whenever Sander is RunningAt a time Properly Connecting to Power Source OutletGrounded /n Ul OUTLETs Unpacking and checking ContentsHAROWABEFORMOUNTINGTOOL& Motor AssernbJyFollowing parts are included with Model Catalog no Mounting Belt and Disc Sander on Craftsman Steel LEG SETAssembly Installing Sanding Disc and Dust TrapWrench Belt Table LockingFlat Spot AssemblyDisc Dust Trap Flat Head Screws TrapTWO Holes TOP Right Hand Screw Dust Trap CoverClips 10-32 X 1/2ON-OFF Switch AssemblyInsert key into switch Place the bolt onto the motor pulley by rotating the pulleyCable Power Cord Motor CordFind plastic cable hanger from among the loose parts Directional ARROW\ Be LT Adjusting SCR EWS Installing Work TablePull Wrenches in this Direction to Apply Tension Belt Locking ScrewBelt Leftmoving To Right Installing Belt Dust TrapBelt Locking Screw Drive PulleyAssembWy Installing BackstopGetting to know your belt and disc sander ANY Aojustm EntsFrom Disc Positioning Lock Screw Stop Tilt Lock NUT Belt Adjusting Screw ONE on Each SideGe ng to know you r belt and disc sander Raise the table and loosen the lock nut using a 7/16 wrenchPlace. It is locked uing the 1/2 wrench Lock NUtBasic operation Before Using the SanderBefore Each USE Before freeing any jammed material Surface Finishing on Abrasive BeltFor finishing long pieces, remove the backstop END Finishing on Abrasive BeltCurved Edges Sears Recommends Following Accessories Motor Maintenance LubricationCausing thebelt to sli CAT. noBox Motor wd! notProtector Open, only TooRemedy Trouble Shooting -- MotorLOW Voltage Supplied With Parts ListHardware for Mounting Tool & Motor Craftsman Belt and Disc Sander Model no .225900 & 113,225931 47222 Housing, DiscKey Part Description Repair partsWith Plug Outlet Before Proceeding Black Wire to Terminal T1 Green Wire to Green ScrewSwitch Mounting Repair partsDoes Not Include Key No, 3. Order Separately If Required Page BEL T and Disc Sander