FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER
If within one year from the date of purchase th s Craftsman Belt and Disc Sander fails due to a defect in material or workmanship, Sears will repair it, free of charge.
WARRANTY sERVICE IS AVAILABLE BY S MPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
SEARS. ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684
general safety instructions
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and limitations as
well as the specific potential hazards peculiar to this tool.
2.GROUND ALL TOOLS
Th_s foot Is equIPbe(1 with an approved 3.conductor
cord and a
groundmg type receptacle Th_ _reen conductor n the
cord _s tha grounding wire. Never connect the green w_re
_o a hve termmal.
3.KEEP GUARDS IN PLACE
-m working order, and in proper aolustment and align ment
4.REMOVE ADJUSTING KEYS AND WRENCHES
Form habit of ¢heckmg to see tnat keys ana adlustmg
wrenches are removed from tool before turning _t pn
5. KEEP WORK AREACLEAN
C_uttereo areas and benches mwte acc_dems FtOol
must not be Slippery due tO wax or SaWdUSt
6. AVOID DANGEROUS ENVIRONMENT
Don't | LISP Dower | tOOlS | in | damp | or | wet | locations | or ex | |
(_se | them | to raln, | Keep | work | area | well | hghted | Provlde | |
d(lequate | surrounding |
| work | space |
|
|
|
| |
power tools
mask if cutting operation is dustv, and ear protectors
(plugs or muffs) during extended periods of operation.
13. SECU RE WORK
Use clamps or a v_se to hold WOrK When Dractlcal It s
safer than uslng your 13and. frees both hands to operate
tool.
14. DON'T OVERREACH
Keep ProPer foottng and balance at all bmes
15. MAINTAIN TOOLS WITH CARE
Kee_) | tools | snaro | and clean | for | best and | safest | perform |
ance. | Follow | nstruct_ons | for | ubrlcat_ng | ano | changing | |
accessor | les. |
|
|
|
|
|
|
16.DISCONNECT TOOLS
before servicing, when changing accessories SUCh as
blades. P_ts. cutters etc
17. AVOID ACCIDENTAL STARTING
Make sure swdch s m "OFF" position before pluggmg
Ln
18.USE RECOMMENDED ACCESSORIES
Consult tbeowner's manua for recommendedaccessories.
Follow the nslrucPons that accompanythe accessories.
The use of mproDer accessories may cause hazards.
7.KEEP CHILDREN AWAY
All visitors should be keot a safed_stance from work area
8. MAKE WORKSHOP CHILD-PROOF
w_tn {_adlpcks rnastel swltche_ or r)V remownq starter
I<eVS
9.DON'T FORCE TOOL
It wdl do the IOb bt, tter ana safer at the rate to{ which
•was des_qneo
10.USE RIGHT TOOL
_OCt't foFce too ol dttaci_mPnt to (30 a 1o13 r'[ was not
ties gnea for
11. WEAR PROPER APPAREL
Do not weal loose cIothlnh gloves, rleckttes or _ewelrv
brags. _.,rlstwatcnesl to get caugn[ in movlng parts
NONSLIP footwear s iecommended Weal protective
nalr covering to contain long halt. Roll long Sleeves
above the elbow
12. USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with ANSI Z87,1) at all times. Everyday eyeglasses only have impact resistant
lenses, mey are NOT safety glasses. Also use face or dust
19. NEVER STAND ON TOOL
Serious ]nlury could OCCUI _f the tool _s tipper or tf the
cuttmg tool _s accidentally contacteP
Do not store materials 3bove or near the tool such mat
it s necessar, to stand on the tool to reach them
20. CHECK | DAMAGED | PARTS |
|
|
|
|
|
|
| ||||||
Before | furmer | use | of | the | tool | a guard |
| or | other |
| _)art | thai | |||
_s | Clamaged | should | be | carefully |
| checked | to | ensure | that LI | ||||||
will | operate |
| properly | and | perform | its |
| intended | function | ||||||
Check | for | alignment |
| of | mPvmg | Darts |
| bJndmg | of | mowng | |||||
baits, | breakage | of | _arts, | mountmg, | and | any | other | con | |||||||
dd_ons | that | may | affect | ts | operation. |
| A | guaro |
| Ol | othe_ | ||||
oa_I | that | is | damage(] | should |
| De properly | repaired | Ol | |||||||
replaced
21.DIRECTION OF FEED
Feed work mto a blade or cutter aga nst the ChrPCtion Of
rotation of the blade or cutter only
22. NEVER LEAVE TOOL RUNN NG
UN ATTENDED
Turn power off _)on't leave too_ unt_l t comps _o a coml)lete stop